|
09-06-2006, 02:37 AM
|
#1
|
Montana Master
Join Date: Jul 2005
Location: Fort Myers
Posts: 5,933
M.O.C. #4282
|
Brake settings?
I have two settings on my brake. Please refresh my memory on the two settings. I have mine set at 2.0 (front dial) and 9 (side dial) on my Draw Tite II controller. I believe the 2.0 is how hard the trailer brakes grab? If I set them any higher, they REALLY grab and release with a hard jerk.
What is everyone else using for these numbers? I know we did this last year sometime?
|
|
|
09-06-2006, 02:32 PM
|
#2
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
I'm not familiar with your controller but, on every aftermarket controller I ever used, the side adjustment determined when the trailer brakes engaged relative to the truck brakes and the front adjustment was for how hard to apply the brakes. Sometimes that side one is described as "setting the level of the controller", but the result is the same.
See another Montana or Mountaineer on the road? Flash lights twice, it might be one of us!
Steve Reigle (pronounced Regal)
Fulltiming since 3/21/03
'07 3400RL
'05 Ford F250 SD Lariat CC SB 6.0L PSD/TS FX4 4x4
Our RV Travels (now Firefox-compatible)
|
|
|
09-06-2006, 04:39 PM
|
#3
|
Montana Master
Join Date: Aug 2004
Location: Fallon
Posts: 6,064
M.O.C. #1989
|
Dave
What do the directions say? Did you read them? On our Prodigy it had a step by step setup. We drove around the block several times to get it set. It is so far superior to the old one we had I can't even believe it. I was ready to quit this RVing until we got the new one. The old one was worse than the worse ride at Disneyland. But we were never given directions, so we didn't know how to set it up. Directions are wonderful.
Happy trails.......................
Sue and Ed Rowe
Hemet California 2005 3400RL 2006 GMC 3500 Dually, D/A, Crew Cab, Long Bed
|
|
|
09-06-2006, 07:32 PM
|
#4
|
Montana Master
Join Date: Jan 2004
Location: Down the Road
Posts: 5,627
M.O.C. #889
|
If you dont have directions, have you looked at Draw Tite's website?? Maybe they offer a download that will answer your questions. Sorry I cant help, I run the Tekonsha Voyager controller.
2004 Chevy Silverado LT 2500HD CrewCab Duramax
2004 Montana 3400RL
|
|
|
09-07-2006, 04:22 AM
|
#5
|
Montana Master
Join Date: Jul 2005
Location: Fort Myers
Posts: 5,933
M.O.C. #4282
|
The controller came with the truck - no instructions. I just have downloaded and read the adjustment instructions.
"Output Control" is the front knob. "Sync Control" is the side dial.
I will try the setup instructions and see if these help. Seems I tried this before, and still had the jerking. I will give this a try before heading south next Wed. If I can't seem to get rid of this, I have also written down the toll free #. Also, Prodigy controllers don''t cost THAT much, do they?
What does everyone else run on their "output" and "sync" numbers???
Thanks, Steve, Sue, and Dave!
*On Edit~ The initial setup numbers call for a 2.0 for output and a 4o (lower case "o" is correct for this controller) for sync. Doesn't this seem a bit low for our Montanas?
|
|
|
09-07-2006, 06:54 AM
|
#6
|
Montana Fan
Join Date: Oct 2005
Location: Franklin
Posts: 126
M.O.C. #4721
|
Hey Dave,
I have the same set up as you, The side slide controls how fast it grabs and the top knob is how hard it grabs. I have mine set at side slide #3 And top at#6.5 this seems good for me. But my unit is'nt as heavy as yours, you have to play with it and see what works for you.
Live Well, Love Much, Laugh Often
Dano & Wife of Dano
Franklin, GA
2006 Montana 3000RK
2006 Dodge 3500 Diesel
Quad Cab 4WD Dually Laramie Pkg
16K Draw-Tite Swivel Hitch
Draw-Tite Brake Controller
|
|
|
09-07-2006, 07:16 AM
|
#7
|
Montana Master
Join Date: Jul 2005
Location: Fort Myers
Posts: 5,933
M.O.C. #4282
|
Thanks, Dano. I will try this. I have tried several configurations, but apparently haven't hit the right combination yet. This really should help.
|
|
|
09-07-2006, 11:29 AM
|
#8
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
Dave, when a manual gives you an initial setting it's just a starting point. From there you are supposed to drive up to about 20 or 25 mph, pull the manual brake handle. You adjust the front knob (leave the side one alone once you have it set!) until it just locks the brakes when you do that. However, the Prodigy I had would never lock the Montana brakes so I just got it to where it was braking hard. Then when on the road I adjusted to what I was comfortable with as far as stopping ability. Once I got it set right for us I never had to touch it again. The first critical thing is to get that Sync Control set properly. If that's not right nothing you do with the other knob is going to get the braking right. Pay real close attention to the instructions for setting that side dial.
See another Montana or Mountaineer on the road? Flash lights twice, it might be one of us!
Steve Reigle (pronounced Regal)
Fulltiming since 3/21/03
'07 3400RL
'05 Ford F250 SD Lariat CC SB 6.0L PSD/TS FX4 4x4
Our RV Travels (now Firefox-compatible)
|
|
|
09-07-2006, 01:35 PM
|
#9
|
Montana Master
Join Date: Jan 2005
Location: Cooper
Posts: 1,230
M.O.C. #3029
|
Dave-
I am using the same brake controller that you are if yours is labeled Activator II. I have had this controller in three TV's and the Montana is the second trailer. The settings for both trailers were about the same. The side is set is set at 6 and the top is 3. This works well when normal stopping. Sometimes when I am maneuvering around trying to get the trailer parked I will lower the top to 2.5 or maybe even down to 2.0 to keep the brakes from grabbing too hard.
Here is a link for the manual to this controller:
http://www.bsaohio.com/instructs/550...ke%20manual%22
Charlie
2001 F-250 Lariat SC 4x2 LB 7.3L PSD
BD Power ECM 80 HP Performance Chip
BD Power X-Monitor LED Digital Gauges
Firestone Ride-Rite Air Bags
2005 3295RK
|
|
|
09-07-2006, 02:25 PM
|
#10
|
Montana Master
Join Date: Jul 2005
Location: Fort Myers
Posts: 5,933
M.O.C. #4282
|
Thanks, Steve! This has been a frustrating learning curve for me. Think it getting ready to smooth out now (pardon the pun).
Charlie, I also have the Activator II. Sounds like your numbers match up pretty good with Dano's settings. I have backed up and hooked up the umbillical and set my controller to these numbers. I will follow the manual that I just downloaded as far as any adjustments that need to be made, but I feel very comfortable the the range of numbers that you guys have given me here to start with.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|