Recalibrating Auto Level on a 2026 Montana 3100

[Ksthis]

How do I recalibrate our auto level on our 26 Montana 3100 recalibrate. It's way off after it sets itself i have to use a level and do it manually.

 

[Carl n Susan]

LCI substantially changed the Auto Level process with the introduction of the Titan Leveling System in 2024. The Resources tab, above in the blue bar, gets you to a ton of manuals. You want the click on the Systems list and look for the Titan Leveling System manual. Just in case, here is the link:

Titan Leveling System (2024 and Later) ccd-0007709

The 2024 (and later) Montanas come with the new, improved Titan Leveling System by LCI. This is the first substantive change to the operator interface (aka touch pad) since the system's introduction in 2012.

www.montanaowners.com

I don't know how this new system works as I have the older LevelUp system. The new Titan system has a pre-programmed "Level" setting that it appears you can't change. You apparently can "Add" additional set points and select them at Auto Level time, but from what I read it doesn't reset the factory setting. LCI must believe their "Level" setting is sacrosanct.

 

[Daryles]

The new Titan leveling system SUCKS !!!
You had much more granular control over the jacks with the Level-Up system.
Also there is no room to raise your jack to a mounting hole if you consider them too low (dragging).
I'll have to raise the pin box or install air bags on the truck.

 

[Dhuhn]

I disagree with Daryles The Titan system is more user friendly than old system.
Also you can raise the legs if they are too low I have done it with no problem.

 

[A&D Bond]

How do I recalibrate our auto level on our 26 Montana 3100 recalibrate. It's way off after it sets itself i have to use a level and do it manually.

I am not sure how to recalibrate, but if I choose a self-leveling option besides factory level, the trailer is not level. When I use the factory level option, it is perfect. Hope this helps

 

[Scubado]

I took a 4' level and did a recalibrate on mine. It was very easy to do, and I saved the setting as the "Factory Setting". I don't remember how I did it without looking at the pad. I can look at it over the weekend and refresh my memory if you need me to.

 

[Ksthis]

Would greatly appreciate it. I'm still trying to figure it out.

 

[Scubado]

Sorry I took so long to respond. I had to have the trailer in front of me.

To MANUAL LEVEL

1 - Turn on the pad and put in your unlock code
2 - Press OPTIONS
3 - Press MODES
4 - Press MANUAL
Then press Front L or R and Extend or Retract as needed. Then go to the Rear L or R or Both and Extend or Retract as needed.
Note Press L or R to pick it and Press L or R again to deselect it.
Go back to the Front again if you need to readjust it.

To set AUTO LEVEL

1 - Turn on the pad and put in your unlock code
2 - Press OPTIONS
3 - Press SETPOINTS
4 - Press whichever SETPOINT that you want to set. You have a choice of FACTORY SETPOINT, OPTION 2, OPTION 3 or OPTION 4
I picked the FACTORY SETPOINT. Pick whichever SETPOINT that you choose to set or set multiple SETPOINTS. (I have no clue why they give you so many choices)
5 - Pick CHANGE
6 - Adjust level if necessary as you did above.
7 - After you are all level Press SET.
That is it you are all set and your level(s) have been saved. You can either let the keypad time out and turn off or keep pressing "X" then the back arrow until you get back to the home screen.
It really isn't very hard to do. Biggest problem is when the keypad times out and turns off you have to press all the buttons to get back to the page you were on to continue your adjustments. I had my wife inside with a 2-way radio watching the level and letting me know the readings as I adjusted them.
Good luck!
Please let me know if this all worked for you and my instructions all make sense.

 

[Scubado]

Would greatly appreciate it. I'm still trying to figure it out.

Did my tutorial help you out?