2017 Montana 3731FL

[Lakegirl0514]

Thank you for the reply! Tried all that. Can't seem to get the signal from the outside to the tv. Any other ideas?

[stengels]

Welcome to the forum and enjoy your rig.

[BB_TX]

Originally Posted by Lakegirl0514

Thank you for the reply! Tried all that. Can't seem to get the signal from the outside to the tv. Any other ideas?

I would recommend you start a new discussion specific to your issues rather than tag on this discussion. I think you would get more reads and probably more suggestions.

[R Berry]

Got mine in April took it to Maryland two weeks ago, Minor problems, One of the slide outs (Bed) was hard to close, So if it wouldn't close ether would the two kitchen slides because they all three work together.

[R Berry]

Originally Posted by BB_TX

First question about the DVD player would be, did you select the proper source input on the TV? You may have to trace the HDMI cable, or possibly a video cable, from the DVD player to the TV to see which input it is using.

Just a heads up, one day I was looking down inside the area where the TV comes up from behind the fireplace. I notice the power cable for the fireplace was laying on the actuator of the TV. I unplug the fireplace and examine the cord and found that it was smashed and the cord was cut and I could see the three wires in side the cord. (A Fire Hazard) I left the fireplace unplug and when I got back home I took it to the dealer to get it replace. You might check yours.

[R Berry]

Originally Posted by Lakegirl0514

Thank you for the reply! Tried all that. Can't seem to get the signal from the outside to the tv. Any other ideas?

I don't know if you got this problem fix yet, but I just setup my RV and I have city cable available. it took me awhile to get it to work but my nephew told me that there should be a switch to turn off the antenna and I found one in the bedroom closet top right side. A push button with a little green light, so I turn it off but still have problems. So I tried all three of my cable in puts and of course they are miss label just like my lights switches in the panel box.

[Jay Bird]

Welcome to the forum from NC

[Sckfiver]

So far have been to camping world to repair an intermittent drivers side front living slide failure plus level board problem. Finally replaced one of the synchronized motors and cables and circuit board for leveling problem. Will be using it the next two weeks. The slide has worked a couple of times so far, so keeping our fingures crossed. The rv has been in for repair much more time than we have had it in our possession. A few other minor problems, loosing screws out trim etc., taking care of them myself with different screws and lock-nuts. Once all is working I am sure we will get to enjoy the RV.

[phillyg]

To the OP, I forgot to mention that what you think might be a low battery situation might be a 40a auto-reset fuse for the hydraulic slides and level-up controls. Lippert has a service bulletin explaining that the 40a fuse can be replaced with a 80a fuse.

[teichrott]

We are fortunate to have purchased our Montana last year. We are using it primarily for horse shows and found herself in Massachusetts in April and snow. The main furnace heating area is doing wonderful but I am finding that the bedroom has been relatively cold. I made sure that the heater is on furnace and not on heat pump as it is in the 30s. But it is still cold. Am I missing something?

[teichrott]

Try the switch near the cable inlet in the closet of the master bedroom. Switches from TV cable to TV antenna.

[CaptnJohn]

Originally Posted by teichrott

We are fortunate to have purchased our Montana last year. We are using it primarily for horse shows and found herself in Massachusetts in April and snow. The main furnace heating area is doing wonderful but I am finding that the bedroom has been relatively cold. I made sure that the heater is on furnace and not on heat pump as it is in the 30s. But it is still cold. Am I missing something?

The furnace should heat the bedroom as well. If it is cold the ductwork may have come loose or may never have been connected at all. Search it from the furnace to the register by going through the basement.

[teichrott]

I'm concerned that I don't know about the basement.. lol

[Troutn]

We were very interested in that floorplan but bought a 3791RD. Bascially, the floor plans are flipped.

[teichrott]

I love the bedroom in the back... Wasn't a fan of the Cafe style seating in the kitchen.. all beautiful though.

[cghsatx]

I have a new 2019 3731 and like the floor plan but am not too happy with much else so far

[CaptnJohn]

Originally Posted by cghsatx

I have a new 2019 3731 and like the floor plan but am not too happy with much else so far

In my last 3 I found it took about a year or 200 nights to get the little stuff fixed and all mods I wanted done.

[cghsatx]

Yes, the table/chairs setup in a 2019 3731 is awful and practically useless. I only use 2 of the four chairs and even that is cramped. If the shade trim didn't stick out so far, there would be a little more room to use/enjoy sitting at the table. Not to mention having to crawl around on the floor latching the chairs together when it time to take down.

[CaptnJohn]

We leave 2 chairs at home.

[cghsatx]

CaptnJohn - I just joined the forum. Where do you add the signature info ie "John & Patty" , tow vehicle etc.

Am learning the forum might be a lot more fun than dealing with the local service dept and feeling financially scammed at an age where you don't spending $ to have some fun but cant afford to throw too much of it away