|
09-21-2020, 12:29 PM
|
#1
|
Montana Master
Join Date: Oct 2018
Location: Anderson
Posts: 2,591
M.O.C. #22835
|
All screwed up!
Well, kind of!
Noticed today that the back screen door had some wiggle to it when opening and closing, so got out the old Robertson screw driver and tightened the screws down. Noticed also, the door itself had loose screws. So, I decided to check the front door too. Sure enough, every one was wiggling loose. Tightened them all up.
So then decided to check some others, and sure enough, they were loose too: Screws holding on the ladder. Screws holding on those little square things on the front of the slides. Screws on the sides of the slides. Screws holding the cable connections for the slides. Screws around the furnace cover. Screws holding on trim. Screws holding on the fenders.
Well, the list can go on and on. I need to get on a ladder and then the roof now and check them all up higher where I couldn't reach. I'll do that later today.
Although it's a 2019 model, we've had it 2 years now in September. I've never checked the outside screws for tightness, but glad I did now.
Got a few more to go, and only takes a few minutes to get around everything. And I figure, this is pretty good minor maintenance anyway.
So, now... I'm litterally "All screwed up."
If you haven't checked yours in a year or two, it might be a good thing to check right now!
__________________
Who you are right now is a sum total off all you use to be.
2019 Montana High Country 375FL
2014 Chevy Silverado Duramax, 6.6L Dually
|
|
|
09-21-2020, 12:41 PM
|
#2
|
Montana Master
Join Date: Oct 2004
Location: Salem
Posts: 7,550
M.O.C. #2283
|
You came to the right bunch. We are all screwed up.
Lynwood
|
|
|
09-21-2020, 02:19 PM
|
#3
|
Montana Master
Join Date: Oct 2006
Location: McKinney
Posts: 7,167
M.O.C. #6433
|
While you are still “all screwed up”, go into your load distribution center and tighten all your hot, neutral, 12 vdc, and ground screws, preferably with power disconnected. Probably find some loose there also.
__________________
Bill & Patricia
Riley, our Golden
2007 3075RL (recently sold, currently without)
|
|
|
09-21-2020, 07:32 PM
|
#4
|
Montana Master
Join Date: Jun 2018
Location: Carson City
Posts: 2,017
M.O.C. #21963
|
Good thing you can tighten those screws. A bunch of mine that are loose is because they are stripped.
__________________
2016 3160, Legacy, Sailuns, Splendide 2100 xc vented, 1 1/2" axle lift blocks, disk brakes. 2014 Ram 3500 SRW SWB 4X4 6.7 Aisin Mega Cab, EBC slotted disks and brakes, Titan fuel tank.
|
|
|
09-21-2020, 08:17 PM
|
#5
|
Montana Master
Join Date: Feb 2012
Location: Lake Gaston
Posts: 8,773
M.O.C. #12156
|
And I had some that screwed into nothing
__________________
Mike and Lorraine
2002 3655 FL, 2005 3650RK
2010 3665RE, 2015 3910FB
F350 crew cab dually 6.7
|
|
|
09-22-2020, 09:57 AM
|
#6
|
Montana Master
Join Date: May 2020
Location: UPLAND
Posts: 1,256
M.O.C. #26190
|
Found all the fender trim screws loose too
__________________
2019 Keystone Montana 3560RL, 2020 Chevy 2500 HD, Firestone airbags, Air Lift wireless compressor, Curt gooseneck, 20K Reese Goosebox, TST-507, USMC combat vet & retired LEO. Robert, Anika, Breanna, Dylan (daughter-in-law Stephanie). & our Great Pyrenees Layla
|
|
|
09-22-2020, 10:23 PM
|
#7
|
Site Team
Join Date: Aug 2007
Location: Omaha
Posts: 6,750
M.O.C. #7560
|
Bob-- on the fender skirt screws- go to any hardware store and buy some spring nuts (at least that is what I call them) They are small pieced of spring steel that are curved and a small hole in the middle. Take out the loose screws and put the spring nuts on the back. No more problem with the screws loosening up or coming out!
|
|
|
10-31-2020, 03:23 PM
|
#8
|
Established Member
Join Date: Nov 2003
Location: Grand Marais
Posts: 12
M.O.C. #615
|
I found loose ones on my 2020 3740 when I got it home from the dealer, who is 2 1/2 hours away. I took each one out and put a dap of silicone on screw and put them back in. We then went on a 2200 mile trip to the Black Hills and all screws stayed tight.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|