|
07-26-2005, 02:59 PM
|
#1
|
Established Member
Join Date: Jul 2004
Location: Aurora
Posts: 36
M.O.C. #1794
|
Fresh Water Tank Leak
Sometime ago I read about someone who had repaired their tank and it showed a picture of it I believe.
If so where would I find it -- we may have frozen up this past winter that cause this problem.
Give me some ideas/options please. Thanks again.
|
|
|
07-27-2005, 01:31 AM
|
#2
|
Montana Fan
Join Date: Jan 2005
Location: Carpentersville
Posts: 468
M.O.C. #2785
|
I was at least one of them. Do a search for "plastic welding". You will need to find out what kind of plastic the fresh water tank is made of. You could call a Montana customer relations person as that is how I found out the holding tanks are made of ABS.
Eric
|
|
|
08-03-2005, 02:58 AM
|
#3
|
Established Member
Join Date: Jul 2004
Location: Aurora
Posts: 36
M.O.C. #1794
|
Keystone say's it's OK to use Plastic Weld. Any ideas on how to get to the tank from underneath -- I see black underbelly material and stabilizer jacks. Need any advice you may have. Thanks
|
|
|
08-03-2005, 03:28 AM
|
#4
|
Montana Master
Join Date: Oct 2003
Location: Malta
Posts: 3,075
M.O.C. #607
|
you would have to remove the underbelly to get to it. be prepared to have some of the screws snap off during the process though.personally I let the dealer do it last time just so I wouldn't have the agravation. (mine wasn't for a tank leak though)
|
|
|
08-03-2005, 08:00 PM
|
#5
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
The tank is probably close to where the filler connection is. If you'll post which model of Montana you have maybe someone can tell you for sure. Once you know where it is located you'll need to drop the belly pan for that area. As Billy Ray said, have some spare screws on hand as they do tend to break fairly easily. Once you remove that section of the belly pan you should see the tank and be able to access it. If you have the Arctic Package there will be a sheet of insulated material you'll need to fold back also.
Do you think the tank contents froze or maybe the water lines?
|
|
|
08-04-2005, 06:50 AM
|
#6
|
Established Member
Join Date: Jul 2004
Location: Aurora
Posts: 36
M.O.C. #1794
|
The Model is 2750RK -- Not sure if it is the tank or water line but last Nov./Dec. we used our trailer and thought we had it fixed so it wouldn't freeze. We insulated the water lines in the under belly, and put styro foam facuet covers over the Fresh Water Tank Drain and that's where we had a large ice ball. It filled up the styrofoam cover -- removed the ice and cover -- drained the tank and came home and winterized it for the winter months. Went to use it last week and saw water seeping from the under belly area close to the drain. What are your thoughts? Do you have to cut any of the under belly material or are they in sections. From what I saw it looks quite involved due to the Stablizer Jacks. Maybe I need to take a closer look. Appreciate any and all ideas. Thanks
Quote:
quote:Originally posted by sreigle
The tank is probably close to where the filler connection is. If you'll post which model of Montana you have maybe someone can tell you for sure. Once you know where it is located you'll need to drop the belly pan for that area. As Billy Ray said, have some spare screws on hand as they do tend to break fairly easily. Once you remove that section of the belly pan you should see the tank and be able to access it. If you have the Arctic Package there will be a sheet of insulated material you'll need to fold back also.
Do you think the tank contents froze or maybe the water lines?
|
|
|
|
08-05-2005, 04:39 AM
|
#7
|
Established Member
Join Date: Jul 2004
Location: Aurora
Posts: 36
M.O.C. #1794
|
We have our problem resolved, thanks to pointers from all the nice people using this site. We dropped the underbelly and saw a small leak where the line goes into the tank. Repaired that and buckled up the bottom and we are on our way for now. Thanks again to all.
|
|
|
08-05-2005, 03:21 PM
|
#8
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
WildBill, I'd like to comment on the styrofoam on the low point drains. If you are in any serious cold, say mid teens or below, I really don't think those covers are going to be enough protection. I tried everything to stop those from freezing, including foam pipe insulation, roll insulation wrapped and duct taped, you name it. But they'd still eventually freeze. The freezing is not necessarily bad until it freezes up into the tee of the line and then it stops the water flow, as you likely already know. I finally heat taped those low point drains, then wrapped that with insulation and duct taped over all that. We then got down to 3 degrees F without freezing. But at 5 below they froze anyhow.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|