|
10-29-2006, 01:00 AM
|
#1
|
Montana Master
Join Date: Oct 2005
Location:
Posts: 1,568
M.O.C. #4890
|
Cutting holes in your interior panels.
I think most of you know this, but the hollow interior walls of an RV are only 1/8th " thick and a utility knife with a sharp blade will cut through in about 4 passes. This is handy in tight corners where a power tool would not work or if you are worried about wires or pipes in the wall. Yesterday I cut out the panel behind my toilet using a utility knife and it works pretty good. The inner panel is woodgrain and I was able to salvage that for use in my renovations.
I took the tube tv out and put a thin LCD in it's place. Now I am doing the renovations to access the space behind the old TV. My original plan was to put a door on the side over the stairway but there is a plumbing vent and wires in that wall so that would be very difficult to do.
Instead I am going to put two doors just behind the toilet. This gives a wider access to the space and that wall is completely hollow with only a thin stud in the centre which makes this job a lot easier.
|
|
|
10-29-2006, 02:44 AM
|
#2
|
Montana Master
Join Date: Jul 2006
Location: K.C.
Posts: 11,731
M.O.C. #5980
|
Good tips, Buddy.
When you can use a power tool, get a plunge router like tool, the Zip router, Lowe's. You can set the depth and cut into the wall just short of coming through the other side, then finish with a knife, or just push it out. This is super on the Black under belly covering as well, that way you can cut an access hole without cutting hydraulic or electrical lines that are just laying on the panel.
Ozz
|
|
|
10-29-2006, 04:20 AM
|
#3
|
Montana Master
Join Date: Feb 2003
Location: Englewood
Posts: 3,095
M.O.C. #164
|
I have often thought of cutting into the wall in the Potty Room and accessimg
the cupboard above the TV in our 2955.That cupboard is so high and hard to reach from the living area.
|
|
|
10-29-2006, 04:57 AM
|
#4
|
Montana Master
Join Date: Aug 2006
Location: Lone Tree
Posts: 5,615
M.O.C. #6109
|
Wrenchtraveler -
When looking at new Montys - that was the first thing Dory noticed was the cupboard access above the toilet into the cabinet above the TV. That was a great improvement, as it eliminated the head knocker cabinet in front of the toilet and utilized at least half of the cabinet over the TV far better than ours. I'm assuming your newer rig already has these cabinet doors? Are you talking about adding more below them?
Ken - Keystone must have been reading your mind.
|
|
|
10-30-2006, 02:08 AM
|
#5
|
Montana Master
Join Date: Oct 2005
Location:
Posts: 1,568
M.O.C. #4890
|
That's right Brad , I have two doors left from the fireplace install and they will go under the two doors in there. The top cabinet is quite large but the new one below will be way bigger.
I will post some pics when it is done.
|
|
|
11-04-2006, 12:20 PM
|
#6
|
Montana Fan
Join Date: Sep 2006
Location: morgans point
Posts: 403
M.O.C. #6292
|
Thanks Don, great idea for the access doors. Barb wuld love to have that done for easy access to the cabinet above the TV.
bob
|
|
|
11-05-2006, 08:48 AM
|
#7
|
Montana Master
Join Date: Oct 2003
Location: Malta
Posts: 3,075
M.O.C. #607
|
how about a thin panel tv in the bathroom? LOL
|
|
|
11-05-2006, 09:09 AM
|
#8
|
Montana Master
Join Date: Oct 2006
Location: Choctaw
Posts: 530
M.O.C. #6364
|
A Dremel tool with a cutting disk can also get into tight corners. I've used it at home to cut sheetrock for computer LAN drops as well as installing outlets in my old RV.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|