|
|
09-26-2021, 01:48 PM
|
#21
|
New Member
Join Date: Aug 2020
Location: Bowling Green
Posts: 8
M.O.C. #26975
|
Quote:
Originally Posted by RicknTee
Hi All, I have a 2017 3160RL with 6pt Hyd Levelers. I bought it in March of this year (2021) and have had issues with the levelers almost every trip out. In the last few trips the levelers timeout. The voltage on the panel indicates 12.4 volts most of the time when this happens. So today after unhitching, but before unplugging from my truck I put a volt meter on my batteries and it registered 13.4v. After disconnecting from my truck, it read 13.2v, howver the panel said 12.5v. I can always level with manual mode, but I want the auto level to work like it should.
A few weeks ago I found a loose connection or two and tightened those up. I figure it's either got to be a wire connection issue, controller or panel problem. I just purchased these Interstate 6v in May and I checked the water level and all is good.
Hopefully someone has had this issue and can help me or let me know if I'm on the right path.
Thanks!
|
What kind of battery's do you have. If the dealer installed them they are most likely a battery for starting an outboard motor or a trolling motor. If they are rated CCA they are not what you need for RV you need a battery rated in amp hours. Also if they are lead acid of any kind they are only good for 50% discharge before degrade the battery.
Plus the way The larger RVs are wired you're lucky if you'll get 2 amps to charge the battery.
|
|
|
09-26-2021, 04:17 PM
|
#22
|
Established Member
Join Date: Mar 2021
Location: Meridian
Posts: 49
M.O.C. #28444
|
Project 98% Complete
I want to thank everyone for their expertise in this issue. I got breakers and all installed, just waiting on my terminal bus bar to complete it. Test after install was a success, no errors. I had 4awg cables made at a battery dealer, nice cables, made to length. I screwed up on 2, so Monday is back for proper length. Here's a picture of what I have completed.
Again thanks for all your help!
__________________
Rick and Theresa
2017 Montana 3160RL
2020 Chevrolet 3500HD, Duramax
|
|
|
09-26-2021, 04:22 PM
|
#23
|
Established Member
Join Date: Mar 2021
Location: Meridian
Posts: 49
M.O.C. #28444
|
I finally found then on Amazon and now have them installed. Thanks for pictures.
__________________
Rick and Theresa
2017 Montana 3160RL
2020 Chevrolet 3500HD, Duramax
|
|
|
09-26-2021, 05:04 PM
|
#24
|
Montana Master
Join Date: May 2019
Location: Alton
Posts: 2,654
M.O.C. #24086
|
Quote:
Originally Posted by RicknTee
I finally found then on Amazon and now have them installed. Thanks for pictures.
|
Nice job!
|
|
|
09-26-2021, 06:10 PM
|
#25
|
Montana Master
Join Date: May 2016
Location: Cuyahoga Falls
Posts: 699
M.O.C. #18572
|
I know all of the replies have been in regard to the 50A breaker and that is the recommended upgrade. That being said, in your original post you stated you could always level your rig manually but wanted auto to work properly. The timing out of the auto level tells me that the system can’t “find” level. Several things could be at issue. A sensor or reset system level or the nose of your rig is too low when starting auto level.
JMHO
|
|
|
09-27-2021, 10:16 AM
|
#26
|
Established Member
Join Date: Dec 2019
Location: Blanchard
Posts: 19
M.O.C. #25551
|
Quote:
Originally Posted by 432bartman
I found out like others that the 50 amp breaker would cause my levelers to stop every so many seconds, and the remedy was putting in an 80 amp breaker, which Lippert recommends. This was all occurring with brand new batteries. Since putting in the 80 amp breaker, my levelers and slides have no more issues opening/closing or raising/lowering. This could be what you're experiencing.
|
👍 I agree, this fixed our 3721☝️
|
|
|
09-27-2021, 10:22 AM
|
#27
|
Established Member
Join Date: Mar 2021
Location: Meridian
Posts: 49
M.O.C. #28444
|
Quote:
Originally Posted by JABURKHOLDER
I know all of the replies have been in regard to the 50A breaker and that is the recommended upgrade. That being said, in your original post you stated you could always level your rig manually but wanted auto to work properly. The timing out of the auto level tells me that the system can’t “find” level. Several things could be at issue. A sensor or reset system level or the nose of your rig is too low when starting auto level.
JMHO
|
I have reset the level in August and when the system didn't error it worked. Previously I had the nose too low and got a different error, but read that you needed to have higher than level to use auto level. Once I place the new breaker in, it all worked great, no errors. The real test is this week when we travel and see if it works when we get there.
Regards,
Rick
__________________
Rick and Theresa
2017 Montana 3160RL
2020 Chevrolet 3500HD, Duramax
|
|
|
10-11-2021, 04:04 PM
|
#28
|
Established Member
Join Date: Mar 2021
Location: Meridian
Posts: 49
M.O.C. #28444
|
Final Update
Hi All,
Well I finally got the terminal bus and got it installed. This project seems to have fixed my issue with the levelers. Only have cycled it twice since, but no issues.
Here is a picture of the project completed. I took the advice that you all gave me and:
Installed 80amp Manual Breaker for Levelers
Installed 50amp Manual Breaker for Trailer Panel
Installed 30amp Manual Breaker for Accessories (Controllers, Panel, etc..)
Installed a Battery Bar (4 Position)
Installed a Terminal Buss
Mounted it on a 3/8 piece of plywood and installed in front compartment with Batteries.
You all made it so easy to get done - Thanks!
Rick
__________________
Rick and Theresa
2017 Montana 3160RL
2020 Chevrolet 3500HD, Duramax
|
|
|
10-11-2021, 04:10 PM
|
#29
|
Montana Fan
Join Date: Oct 2015
Location: Chiefland
Posts: 117
M.O.C. #17939
|
Very nice job and great picture.
__________________
Art and Linda
2007 F250,2000 Montana 2850 RK
2017 F350,2016 Montana 3721 RL
|
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|