|
12-15-2014, 02:22 AM
|
#1
|
Montana Master
Join Date: Apr 2006
Location: Mesa az
Posts: 2,953
M.O.C. #5651
|
Progressive Surge Protector Question
I have a new Mountaineer and had them add a Surge Protector. I got to thinking, if it goes bad, can you/how do you bypass it? It could be kind of a mess without electricity for several days while waiting on one to be shipped.
Thanks.
__________________
Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
|
|
|
12-15-2014, 02:29 AM
|
#2
|
Montana Fan
Join Date: Aug 2005
Location: Crawfordville
Posts: 146
M.O.C. #4328
|
I have one installed and it has a switch on the remote display that will bypass the unit.
From the manual for one with remote display;
This switch is located on the remote panel, and allows the user to bypass the computer circuit in the EMS in the event of computer failure, thus allowing AC power into the RV. This does not disable the surge protection portion of the EMS; however, all other features are disabled.
From the manual for one without remote display;
Enclosed blue jumper wire allows the user to bypass the computer circuit in the EMS in the event of computer failure, thus allowing AC power into the RV. This does not disable the surge protection portion of the EMS; however, all other features are disabled.
|
|
|
12-16-2014, 04:19 PM
|
#3
|
Montana Master
Join Date: Jun 2010
Location: Colorado Springs
Posts: 3,335
M.O.C. #10496
|
DonPd is absolutely correct!
We've NEVER had an issue with ours after install and we've had it installed since 2010. Hope you enjoy the same. The company enjoys a stellar reputation.
__________________
2010 3150RL
LevelUp, Dual 6 volt batteries, Progressive Industries EMS HW50C, Honda EU2000i Generator, Bridgestone Duravis R250 tires, Torklift Glowstep Revolution Stairs, LED Tail lights
2015 RAM 3500 Laramie SRW LB CC Cummins 6.7L Aisin Trans B&W RVK3600
|
|
|
12-16-2014, 05:44 PM
|
#4
|
Montana Fan
Join Date: Dec 2014
Location: Warrior AL, usually
Posts: 184
M.O.C. #15888
|
The Progressive Dynamics unit is an excellent product, and has a very good reputation. however, "stuff" does happen...
The bypass switch for the PD bypasses most of the circuit board in the main box and provides power directly to pull in the contactor (relay contacts), and that switch is what you would normally use to bypass the PD unit. But, if this relay were to fail, or one of the contacts of the relay fail, power would not be passed on through the box on one or both legs of the circuit. With this kind of failure, the only way to restore full power to the camper would be to remove the PD box and splice around it until it can be replaced. The wire into and out of the PD main box is at least #4 gauge, and is too large for common wire nuts.
I carry two "Polaris" connectors in my tool box just in case. They can be used to "splice" large gauge wires together. It's also a good idea to wrap the splice with electrical tape after they are tightened down. They are also handy if you need to pull the PD box to have the MOVs replaced after a lightning strike. It would probably take some digging behind the storage bay wall to get to the unit, but it might save a camping trip!
http://www.globalelectricalsupply.co...or-p/it-4a.htm
|
|
|
12-16-2014, 05:59 PM
|
#5
|
Montana Master
Join Date: Apr 2006
Location: Mesa az
Posts: 2,953
M.O.C. #5651
|
Bama, is there enough 'slack' in the lines to reconnect the wires in an emergency?
__________________
Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
|
|
|
12-17-2014, 03:20 AM
|
#6
|
Montana Master
Join Date: Aug 2007
Location: Waterford
Posts: 3,693
M.O.C. #7500
|
Quote:
quote:Originally posted by twindman
Bama, is there enough 'slack' in the lines to reconnect the wires in an emergency?
|
One thing Montana hasn't scrimped on is the length or power cable inside the trailer. There's more than enough slack to reconnect - and then some!
|
|
|
12-17-2014, 03:39 AM
|
#7
|
Montana Fan
Join Date: Dec 2014
Location: Warrior AL, usually
Posts: 184
M.O.C. #15888
|
Quote:
quote:Originally posted by twindman
Bama, is there enough 'slack' in the lines to reconnect the wires in an emergency?
|
There is on mine, but then, I installed my PD unit and elected to leave lots of slack. In fact I just disconnected the incoming cable from the circuit breaker box, trimmed the ends and ran a new cable to the box. So, lots of slack. This is the easiest way to install one, so I imagine that's how yours was installed. But, even if they installed your PD unit by just cutting the incoming power cable and inserting the box, the cable ends should still have enough slack (once pulled out of the ends of the box) to make a temporary connection. You may have to remove a cable mount if they tied the cable down as a strain relief. The individual wires are so stiff at that point though, they probably left plenty of slack to ease the installation.
So, the answer to your question is... yes.
The hardest part of making a temporary "field repair" like that is getting to it. Most of the time, the PD box is mounted behind a storage bay wall. So, partially unloading the storage bay and removing screws to pull the wall away would be required, but it depends on the location of your PD box installation.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|