|
08-17-2004, 05:12 PM
|
#1
|
Montana Master
Join Date: Mar 2003
Location: Flemington
Posts: 1,373
M.O.C. #242
|
Water in Axles
I slid under the trailer tonite to check the brake wiring since the amperage has been a little low on the last trip. When I pulled the wires out of the axle tube they were wet. I looked around and saw rusty water stains an the backing plates and thrown up on the underside of the trailer. I drilled a 3/16" hole on one end and found the axle tube filled to the haol where the brake wires enter it. I did the same to the other axle and it had about the same amount of water in it.
I did drive in the rain for a few hours last weekend but at no time did I drive through any deep standing water where the axle tube could possibly gotten submerged. I think this is a little strange and was wondering if anyone else has experienced this?
John
|
|
|
08-18-2004, 01:27 AM
|
#2
|
Montana Master
Join Date: Nov 2003
Location: Monominto
Posts: 731
M.O.C. #657
|
Not yet but I'm drilling holes tonight!!!!!!
|
|
|
08-18-2004, 03:04 AM
|
#3
|
Montana Master
Join Date: Jan 2003
Location: Haldimand County
Posts: 2,413
M.O.C. #122
|
Yes, I experienced the exact same thing. I called Alko and they said that they had never heard of such a thing, but did say it would be OK to drill two small holes in the bottom of the axle. I think I drilled 1/8 holes near the spring U-bolts on either side. I did not measure the volume of water that came out, but it had to be a cup or two. Don't forget that your drill will likely get wet. I used a cordless one.
|
|
|
08-18-2004, 10:23 AM
|
#4
|
Montana Master
Join Date: Feb 2004
Location: New Braunfels
Posts: 664
M.O.C. #920
|
Yes, I experienced this shortly after buying the 5ver. I had not been in any high water but had traveled during a heavy rain.
John did the amperage increase after draining the water?
|
|
|
08-18-2004, 10:54 AM
|
#5
|
Montana Master
Join Date: Mar 2003
Location: Flemington
Posts: 1,373
M.O.C. #242
|
I haven't checked yet but I did remove the scotchlock connectors and soldered the wires. The connection at the wheels seems pretty good but the main connection kinda stunk.
John
|
|
|
08-18-2004, 01:26 PM
|
#6
|
Montana Master
Join Date: Jun 2004
Location: Benson
Posts: 3,121
M.O.C. #1658
|
Quote:
quote:Originally posted by NJ Hillbilly
I haven't checked yet but I did remove the scotchlock connectors and soldered the wires. The connection at the wheels seems pretty good but the main connection kinda stunk.
John
|
That's a real good idea, those scotchlock connectors are just trouble waiting to happen. Why in the world Keystone would use those where they will get wet and corrode is beyond me.
|
|
|
08-18-2004, 02:22 PM
|
#7
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
We arrived in this park yesterday with the idea we'll spend part of our ten days here doing all the little projects we've been putting off for lack of time (and energy). After reading this one I'm adding two more projects - drill the holes in the axles and change the brake wire connectors to something more positive. I don't think I kept a soldering iron when we started fulltiming but will take a look. If not, there are alternatives at Lowe's, etc., I think.
|
|
|
08-18-2004, 08:05 PM
|
#8
|
Montana Master
Join Date: Jun 2004
Location: San Antonio
Posts: 1,740
M.O.C. #1757
|
Thanks for the posting. Something to check for. Happyving....
|
|
|
08-19-2004, 02:53 AM
|
#9
|
Montana Master
Join Date: Mar 2003
Location: Flemington
Posts: 1,373
M.O.C. #242
|
I used one of those mini butane torches. They are cheap, disposable and can be used for a number of things. Most hardware stores have them by the cash register.
John
|
|
|
08-19-2004, 04:14 AM
|
#10
|
Montana Master
Join Date: Nov 2002
Location: Hartselle
Posts: 977
M.O.C. #45
|
John
I found the some water in ours also. We hadn't been in any water other than rain. We also had low voltage to the brakes. Upon checking I found that the wires inside the axle tubes were worn through the insulation in 3 places. Replaced the wires to the back axle and the voltage came back up. That is something else to check if you have erratic voltage to the brakes.
|
|
|
08-19-2004, 04:22 AM
|
#11
|
Montana Master
Join Date: Feb 2004
Location: New Braunfels
Posts: 664
M.O.C. #920
|
What is the thought on taking the wire out of the axle and attaching it across the top of the axle? Even if small holes are drilled in the axle, there could still be enough moisture to eventually cause a problem. Good or bad idea?
|
|
|
08-19-2004, 04:37 AM
|
#12
|
Montana Master
Join Date: Mar 2003
Location: Tipton
Posts: 3,646
M.O.C. #191
|
This has been a problem in TT's as long as we have owned one. Had that problem in the both TTs we have owned, BIG TIME. We ran the wires outside the axles. Al just said "I'll be changing ours on the Montana some day, I know it is gonna happen!" Suppose there is some reason that the industry has been doing this for so long, knows there is a problem, and keeps doing it. Wish we knew what the reason was.
|
|
|
08-19-2004, 04:44 AM
|
#13
|
Montana Master
Join Date: Jan 2003
Location: Haldimand County
Posts: 2,413
M.O.C. #122
|
Quote:
quote:Originally posted by Thunderman
What is the thought on taking the wire out of the axle and attaching it across the top of the axle? Even if small holes are drilled in the axle, there could still be enough moisture to eventually cause a problem. Good or bad idea?
|
For what its worth, my concern was more about corrosion in the inside of the axle, than any effect on the insulated wire. I think the wire will be fine in the axle if it is not continuously submerged in water.
I did get rid of those little blue clip-on connectors (are those called "scotchlock"? - never heard that term before.), replacing them with a soldered joint inside a crimp-on connector.
|
|
|
08-19-2004, 06:00 AM
|
#14
|
Montana Master
Join Date: Mar 2003
Location: Flemington
Posts: 1,373
M.O.C. #242
|
You could use wire ties or electrical tape to attach the wires to the outside of the axle. I'll see if things are any better this weekend, if not I'll pull the wires out and replace them.The wire that runs from the trailer cord to the brakes is pretty good sized, then they switched to a smaller wire to jump to the front axle, then a larger wire to cross to the other side. I may replace the short thin wires wit hsomething heavier. I was surprised at the amount of extra wire in the axles, there's probably a foot of extra wire inside.
I can hear all 4 magnets humming so I know all brakes are working.
John
|
|
|
08-19-2004, 07:05 AM
|
#15
|
Montana Master
Join Date: Nov 2002
Location: Hartselle
Posts: 977
M.O.C. #45
|
I used wire ties and electrical tape to attach the wires to the outside of the axle on the top. Tried to pull wire through the axle but it broke into. I used #12 stranded wire with butt connectors. Will have to see if the front axle does the same thing.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Axles
|
Pokernose |
Montana Problems, Problem Solving & Technical Help |
13 |
06-25-2013 09:27 AM |
New Axles
|
mtheo |
Repairs & Service |
3 |
10-02-2010 06:40 AM |
axles
|
bernieb |
General Discussions about our Montanas |
4 |
04-13-2007 09:20 AM |
Axles
|
ashlandcpa |
General Discussions about our Montanas |
26 |
02-23-2007 02:01 PM |
Axles
|
jh1802 |
General Discussions about our Montanas |
11 |
01-11-2005 12:34 PM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|