|
05-03-2011, 02:07 PM
|
#1
|
Montana Master
Join Date: Feb 2005
Location: Sioux Falls
Posts: 729
M.O.C. #3206
|
Over the air tv antennae
We have a part time functioning tv in the slide out entertainment center- My hope is some MOCer has replaced the tv coax from the junction box to the tv in the entertainment center- Is the coax routed through the underbelly? Or does it travel under the roof? How does one install a new coax? My THANX in advance for any knowledge y'all share with me- Don
|
|
|
05-03-2011, 02:11 PM
|
#2
|
Montana Master
Join Date: Feb 2007
Location: Winfield
Posts: 7,327
M.O.C. #6846
|
This is purely supposition, but if it were me trying to do the same, I would be tempted to take one end of the coax, connect it to the other with a threaded connection, gorilla tape all of that together so that the two pieces cannot pull apart, then use the existing coax to pull a new length through. Just a rambling thought that can be taken with a grain of salt.
Bingo
__________________
Bingo and Cathy - Our adventures begin in the hills of WV. We are blessed by our 2014 3850FL Big Sky (previous 2011 3750FL and 2007 3400RL) that we pull with a 2007 Chevy Silverado Classic DRW CC dually.
|
|
|
05-03-2011, 03:55 PM
|
#3
|
Montana Master
Join Date: May 2003
Location: New Bern
Posts: 4,294
M.O.C. #311
|
I tried BINGOS idea it did not work. I ran a new coax along the belly. I used coax designed for underground use. Good luck.
|
|
|
05-04-2011, 02:51 AM
|
#4
|
Montana Master
Join Date: Mar 2006
Posts: 854
M.O.C. #5592
|
Just as a check, have you tried replacing the 'f connectors' the ends of the coax cable? If these are loose they can create a problem. It may save you from installing a new cable.
|
|
|
05-04-2011, 05:15 AM
|
#5
|
Montana Master
Join Date: Sep 2007
Location: Texas City
Posts: 5,736
M.O.C. #7673
|
Good idea on the "F" connector.
If I were going to try and string another coax, that is exactly what I would use. A good nylong string that will withstand some pulling. Tie and tape the string to the end of the existing coax. Pull the old coax out with the string attached. If it all comes through okay, then you just reverse the process and tie the new coax to the string and pull it back through. On pulling the new coax back through I would place another string along side the new coax, ad if successful pulling both through I'd leave the new string and coax in-place with a note attached stating where the coax and string went to. (for the next time.) If nothing pulls through, you are still faced with re-coaxing from the outside.
Good luck.
Whew! To much work!
|
|
|
05-04-2011, 06:35 AM
|
#6
|
Montana Master
Join Date: May 2010
Location: Tampa
Posts: 532
M.O.C. #10378
|
You might want to check all your inside and outside connectors first. I had initial problems with my coax. On mine, it was routed underneath in a large wiring bundle. I found an access point under there and opened the hastily black taped connection around the coax at the barrel connectors, which were the connection point to the entertainment slide. All three in the bundle were loose, taking about 1 1/2 turns to tighten. They were also wet, so I allowed them to dry and bought some self vulcanizing tape. The stuff stretches quite a bit and sticks to itself. Got it at West Marine. It will totally waterproof the connection. Anyhow, it worked for me.
|
|
|
05-04-2011, 08:45 AM
|
#7
|
Montana Master
Join Date: Apr 2007
Location: South Shore
Posts: 6,009
M.O.C. #7110
|
I agree with checking all the connections first, especially any splitters and such. When these go bad they may still look good but I believe they can look good and still be bad.
__________________
2011 GMC 4X4 dually CC, 6.6 Duramax with Allison Transmission. Formally 2001 Montana,2007 3400RL Montana, presently 2018 3401RS Alpine.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|