 |
02-12-2017, 10:50 PM
|
#1
|
|
Montana Master
Join Date: Apr 2006
Location: Mesa az
Posts: 3,033
M.O.C. #5651
|
Landing gear pull pins assembly
I think mine is bent and gets stuck. This is just the pull pin for adjusting the height on the legs. I was looking online for parts, and it appears there are pins with diameter of 3/8 " and also, 7/16 ". I tried to measure and it looks like the hole is 7/16, so I would assume the pin needs to be smaller - 3/8.
Any advice out there? Thanks.
__________________
Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
|
|
|
|
02-21-2017, 08:17 AM
|
#2
|
|
Seasoned Camper
Join Date: Nov 2014
Location: Dover
Posts: 75
M.O.C. #15866
|
These are the pins I used to replace mine on the 318 HC. They were exact fit.
Lippert Components Quick Release 5th Wheel Landing Gear Pull Pins # LC308287. I got them from E trailer. My originals came back bent after the RV was serviced.
|
|
|
|
|
03-07-2017, 09:36 AM
|
#3
|
|
Montana Master
Join Date: Nov 2003
Location: Santa Fe Springs
Posts: 4,189
M.O.C. #639
|
Quote:
Originally Posted by baybum10
These are the pins I used to replace mine on the 318 HC. They were exact fit.
Lippert Components Quick Release 5th Wheel Landing Gear Pull Pins # LC308287. I got them from E trailer. My originals came back bent after the RV was serviced.
|
the only way that those pins can get bent is from the service department dropping the trailer too hard when they move it around the yard with there forklift or whatever they use to move them, most use forklifts with a cup attached to the forks. you should mention that to the service yard that last worked on the trailer.
__________________
Pulling a 2004, 2980 RL an oldie but goodie.
Tow vehicle is a 2009 RED RAM 3500 DRW.
|
|
|
|
|
03-07-2017, 11:29 AM
|
#4
|
|
Montana Master
Join Date: Apr 2006
Location: Mesa az
Posts: 3,033
M.O.C. #5651
|
I got a part at the dealer. When I removed the old one, it was strangely shaped. Sort of like 2 pencils put together end to end, but slightly offset. So they weren't really bent nor were they worn that way. I think they were defective from the factory. My new part works great!!! Thanks for the replies.
__________________
Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
|
|
|
|
|
03-09-2017, 07:09 PM
|
#5
|
|
Seasoned Camper
Join Date: Nov 2014
Location: Dover
Posts: 75
M.O.C. #15866
|
Quote:
Originally Posted by Trailer Trash 2
the only way that those pins can get bent is from the service department dropping the trailer too hard when they move it around the yard with there forklift or whatever they use to move them, most use forklifts with a cup attached to the forks. you should mention that to the service yard that last worked on the trailer.
|
My conclusion also, but the cost of fuel, tolls and my time far exceeded the cost of part and the fifteen minutes to replace. That service was at the end of the warranty period and I have not returned in two years since.
|
|
|
|
|
07-18-2024, 07:00 PM
|
#6
|
|
New Member
Join Date: Jul 2024
Location: Royce City
Posts: 1
M.O.C. #34586
|
Quote:
Originally Posted by baybum10
These are the pins I used to replace mine on the 318 HC. They were exact fit.
Lippert Components Quick Release 5th Wheel Landing Gear Pull Pins # LC308287. I got them from E trailer. My originals came back bent after the RV was serviced.
|
Do you know what size holes you have? Mine appear to be 3/8" and I believe I need a 5/16" pin. 2014 Montana High Country 343RL
|
|
|
|
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Disclaimer:
This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.
All times are GMT -6. The time now is 04:22 PM.
