|
11-10-2009, 02:40 PM
|
#1
|
Established Member
Join Date: Sep 2009
Location: marshall
Posts: 17
M.O.C. #9736
|
Routing of TV cable
How can I find how the cable runs through our RV?
I plugged a working VCR in the cable jack outside (the antenna booster was off)and the bedroom TV had a very fuzzy picture. The LRoom TV was worse.
I printed the diagram of the cable wiring and I'm trying to be sure if I read it correctly but it looks as though the cable goes to the bedroom first. Is this right? If it is then that section from the outside jack to the bedroom is bad. I am checking connections.
The question is, how do I get to that cable to replace it without tearing up something?
How would we bypass the jack and still get cable to both TV's?
Thanks!
Connie
|
|
|
11-10-2009, 03:07 PM
|
#2
|
Established Member
Join Date: Sep 2008
Location: MARSHFIELD
Posts: 16
M.O.C. #8771
|
Seems like a common problem. I had the same problem and was told that I need to do some disconnecting and reconnecting behind the television. Haven't tried it yet. Doesn't sound right, but will work on it when I find time.
Verlyn
|
|
|
11-10-2009, 03:31 PM
|
#3
|
Montana Fan
Join Date: Nov 2004
Location: Raceland
Posts: 409
M.O.C. #2389
|
iam not sure if anyone of us really know how they run that cable, i think only the man at the factory can say how its really run, because there lots of us that seam to have problems trying to get everthing working right ,hope you can find out your answer.........
|
|
|
11-10-2009, 03:46 PM
|
#4
|
Montana Master
Join Date: Apr 2009
Location: Murrieta
Posts: 5,816
M.O.C. #9257
|
The outside connector is for the incoming cable signal (or satellite, but that requires more work and we'll talk about Cable for now). Connect the coax cable from the "campground" cable wire (or your house) into the external coax connector on the side of the Monty (usually near your entertainment center) to enable the television to receive the cable signal. Then you must also set up the televisions to recognize the incoming cable signal by selecting the TV/Video mode button on the remote or selecting channel 3 or 4 if in TV mode. You must also make sure the booster button is OFF to disable the overhead antenna for the Monty.
Using a satellite receiver requires the connecting/disconnecting. If you need help with that let me know if you need explanation.
There is a schematic going around this forum that shows the typical trailer cable/satellite/airwave cabling. If I find it I will post it, or maybe some other member can beat me to the punch since I am slow at finding and knowing how to post such things. But if you are new to this it might need further explanation, but just ask for help.
Good luck with this.
On edit: I hope this link works. It is the forum topic where DONnANNIE posted the schematic.... scan down a few posts to find it:
http://www.montanaowners.com/forums/...erms=schematic
If you have questions please ask the MOC and we'll try and help.
|
|
|
11-11-2009, 01:39 PM
|
#5
|
Established Member
Join Date: Sep 2009
Location: marshall
Posts: 17
M.O.C. #9736
|
Thanks everyone for taking the time to post a tip. I had searched all topics previously and had printed the wiring diagram but it does not show if the cable runs along the roof, floor or sides.
My jumper (short) cable is behind the Livingroom TV and both terminals are connected. The schematic would suggest that the bottom of the short cable is directed to the bedroom when in fact the TOP TERMINAL on ours goes to the bedroom and I did test that run and it is fine. I will keep trying and if I find it I will post it here. Thanks again!
|
|
|
11-13-2009, 12:43 PM
|
#6
|
Montana Fan
Join Date: Oct 2006
Location: East Moriches
Posts: 418
M.O.C. #6436
|
The easiest way I have found to find the routing of the cable wires is to disconnect them all and use an ohm meter. Short one end out and check for continuity on all the other ends. When you find the end put colored tape at each end (different color for each wire)and go to the next wire. When this is done you will have a real good idea how your rig is wired. Good luck.
|
|
|
11-16-2009, 01:47 PM
|
#7
|
Montana Master
Join Date: Apr 2009
Location: Murrieta
Posts: 5,816
M.O.C. #9257
|
iconmae... I think understand your question now. You aren't interested in the schematic or diagram that shows how things are inter-connected, you are looking for the "assembly diagram" for how the wiring is routed within the rig. I have not seen one but don't have any contacts who could provide this. And if you are able to find one, I'd certainly be interested. Unfortunately, I think floor plans and even model years might make a difference. Plus the fact that the assemblers may take liberties on wire runs and may not always use the same route.
Please keep us posted.
|
|
|
11-16-2009, 03:54 PM
|
#8
|
Montana Master
Join Date: Nov 2003
Location: Santa Fe Springs
Posts: 4,189
M.O.C. #639
|
OK I found this It was posted a long time ago and I dont remember who either but it is for a monty.
I hope it helps.
__________________
Pulling a 2004, 2980 RL an oldie but goodie.
Tow vehicle is a 2009 RED RAM 3500 DRW.
|
|
|
11-16-2009, 04:45 PM
|
#9
|
Established Member
Join Date: Sep 2009
Location: marshall
Posts: 17
M.O.C. #9736
|
problem solved - the ends were loose from the connections. I tightened them all and several were definitely loose.
|
|
|
11-17-2009, 09:26 AM
|
#10
|
Montana Fan
Join Date: Oct 2005
Location: St. Petersburg
Posts: 343
M.O.C. #4828
|
Maybe I am dreaming, But, I thought at the factory tour, all the TV cable lines run through the roof. Maybe just a dream. Loose connestions on these cable ends seem to be an every day occurance from the factory. Should be the first thing to check. Have a Good Day
|
|
|
11-17-2009, 12:07 PM
|
#11
|
Established Member
Join Date: Sep 2009
Location: marshall
Posts: 17
M.O.C. #9736
|
It does look as if the park cable connector has cable heading up to the roof. I think this because I took the panel cover off the back of where the refrigerator blows outside and could see the cable but the insulation is hard foam and I couldn't tear it up.
To tighten the connectors, I took the cover plates off and just twisted them on tighter.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|