|
06-03-2021, 06:36 PM
|
#1
|
Established Member
Join Date: Apr 2021
Location: Lenexa
Posts: 19
M.O.C. #28537
|
Bed Slide coming out uneven
The Bed Slide on our 2018 model 3561 won’t fully open. Coming out at an angle snd jams. Thoughts?
|
|
|
06-03-2021, 07:07 PM
|
#2
|
Montana Fan
Join Date: Dec 2011
Location: Livingston
Posts: 350
M.O.C. #12009
|
Have you check your shear pins??
__________________
2014 3850FL
2008 F350 SRW
David and Liz
|
|
|
06-03-2021, 07:17 PM
|
#3
|
Established Member
Join Date: Apr 2021
Location: Lenexa
Posts: 19
M.O.C. #28537
|
Thank you! If I knew where to find them I would. This is a nee unit so I’m a bit lost. Is the drive under the bed? Thank you!!!����*♂️
|
|
|
06-03-2021, 07:23 PM
|
#4
|
Montana Fan
Join Date: Dec 2011
Location: Livingston
Posts: 350
M.O.C. #12009
|
Quote:
Originally Posted by SMurray
Thank you! If I knew where to find them I would. This is a nee unit so I’m a bit lost. Is the drive under the bed? Thank you!!!����*♂️
|
Look under slide and look for two gears, there is a bolt that goes through a square bar that connects to the gears.
__________________
2014 3850FL
2008 F350 SRW
David and Liz
|
|
|
06-03-2021, 07:26 PM
|
#5
|
Site Team
Join Date: Oct 2005
Location: Carmichael - CA
Posts: 7,367
M.O.C. #4831
|
Is the slide hydraulic, cable or Schwintek driven? I would guess cable and you have some broken. One broken cable usually allows the slide to go out evenly. Two broken on the same side would act like what you describe.
__________________
Carl (n Susan)
There is more to life than fuel mileage.
2012 Montana 3700RL Big Sky Package towed by a 2015 Ford F350 6.7L PSD 4WD CC LWB
|
|
|
06-03-2021, 07:27 PM
|
#6
|
Established Member
Join Date: Apr 2021
Location: Lenexa
Posts: 19
M.O.C. #28537
|
Thank you! Was afraid of that. I can’t even see cables. It looks like a up and down channel on both sides of the slide so might be a gear.
|
|
|
06-03-2021, 07:30 PM
|
#7
|
Montana Master
Join Date: Jan 2018
Location: Austin
Posts: 2,421
M.O.C. #21044
|
Your slide mechanism may be a Lippert Schwintek slide. Google that and you can find some isometrics and diagrams that might help. The pic below shows the rails on the slide for a Schwintek mechanism.
Also you may need to resync the slide. There are youtube videos that will show that proceedure.
__________________
MikenDebbie Aggie ‘77 in the sticks near Austin TX
2019 Chevy 3500 High Country DRW
2018 Montana 3921FB
Aussie Gus + Texas Heeler Jimmy
|
|
|
06-03-2021, 08:44 PM
|
#8
|
Established Member
Join Date: Apr 2021
Location: Lenexa
Posts: 19
M.O.C. #28537
|
Yes you are correct! Thank you. It’s coming in at an angle and will not fully extend nor retract. Looks like a service call in the am. Thank you!!!!!
|
|
|
06-04-2021, 04:10 AM
|
#9
|
Montana Master
Join Date: Oct 2019
Location: Jacksonville
Posts: 2,140
M.O.C. #25165
|
Try resynching first. Here's a video from Lippert on how to do that.
__________________
Robert & Diana McNeal
2019 Montana Legacy 3791RD 20th Anniversary Edition
2014 F350 4x4 6.7L SRW
|
|
|
06-04-2021, 04:51 AM
|
#10
|
Established Member
Join Date: Apr 2021
Location: Lenexa
Posts: 19
M.O.C. #28537
|
Thank you. Yes watched that. Issue is the slide only goes out about 20% then binds due to the angle.
|
|
|
06-04-2021, 08:33 PM
|
#11
|
Established Member
Join Date: Apr 2021
Location: Lenexa
Posts: 19
M.O.C. #28537
|
Thank you ALL for the help!!! I deeply appreciate it and love this group for the quick and thorough assistance. I was unable to get a service technician but was lucky to get a highly qualified repair person from about an hour away on the line. He saved me. He literally walked ME through how to find the motor and do the repair! On my 3561 I had to access the motor from inside, next to the bed. Removed a steel flange and pulled back the seals. What I found was the motor had popped up and the motor key was binding in the channel. I tested the motor snd worked fine. Re-seated the motor and reset the outside set screw. Put it all back together and now it’s coming in and out. Next step is to Resync as suggested. I’ll tell you that those RV repair folks earn their $$! Working in tight, hot spaces ain’t fun! Thank you all again! On the road again!!!
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Disclaimer:
This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.
All times are GMT -6. The time now is 11:38 AM.