|
11-04-2015, 05:25 AM
|
#1
|
Montana Master
Join Date: Oct 2013
Location: Ogden
Posts: 638
M.O.C. #13862
|
Dish Network Dish Hopper system in our Montanas?
Has anyone put the Hopper with a Joey into their Montana? My understanding is that the Hopper requires 2 coax cables from the dish to be able to run both the primary Hopper and the Joey at the same time. So, our Montanas only have a single satellite input connector, correct? Would this then be possible to overcome easily?
I have a full size antenna on a tripod (1000.2) and was home to just haul my Hopper from my house along with me on trips.
|
|
|
11-04-2015, 06:43 AM
|
#2
|
Montana Master
Join Date: Feb 2008
Location: Lincoln
Posts: 861
M.O.C. #8154
|
Mark,
Yes, you'll need a solo node from dish. It can be connected directly to your dish via 2 coax cables from your LNB. All of this is done at the dish, outside the rig. The solo node has a single coax that connects to the Montana and then to the Hopper.
I missed your question about the Joey. It can work one of a few ways. There is a second port of the node that coax can be run to the Joey. Using this option, you might have to run coax to the 2nd TV.
Alternatively, you can use a wireless Joey. Dish provides a wireless access point that is attached to the Hopper and an Joey receiver to the 2nd TV. The third option is that some smart Tv's (LG I think is the only one) has a built in Joey app that can us your own wireless network and access the Hopper.
Ken
|
|
|
11-04-2015, 02:13 PM
|
#3
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
We have a Winegard Traveler and did have Dish install the Hopper and Joey, but it didn't seem to involve any extra wiring.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
11-04-2015, 02:19 PM
|
#4
|
Montana Master
Join Date: Jul 2006
Location: K.C.
Posts: 11,731
M.O.C. #5980
|
I think the wiring depends on the sat. dish.
Who do you call to get a package? I called Winegard and they told me to call a number, she just wanted to sell me a receiver.
(I bought a Hopper on ebay)
|
|
|
11-04-2015, 03:54 PM
|
#5
|
Montana Master
Join Date: Oct 2006
Location: McKinney
Posts: 7,226
M.O.C. #6433
|
If you google hopper joey wiring you will get numerous pictures of wiring along with many links to various web sites and videos.
Or you can go to this satellite guys web site and click one of the attached files to bring up Dish pdf files showing wiring diagrams.
__________________
Bill & Patricia
Riley, our Golden
2007 3075RL (recently sold, currently without)
|
|
|
11-05-2015, 09:52 AM
|
#6
|
Montana Fan
Join Date: Aug 2013
Location: Springfield
Posts: 322
M.O.C. #13660
|
Just had this set-up installed in our 2010 3400RL. The service tech installed a triple LNB dish on a pole. He then attached a solo NODE to the dish and ran a single coax cable from the NODE to our service center. He attached a TAP to the other end of the coax which splits the signal. We have 2 satellite and 1 cable TV inputs in our service center. From the tap he ran a cable to each satellite connection, one to the HOST and one to CLIENT (on the tap), Host is the sat connection for the living room where the Hopper is and client is the one for the bedroom where Joey is. In the closet in bedroom he removed the jumper from the antenna booster and connected it to the satellite feed which completes the circuit to the bedroom TV. Connected the coax from the wall behind the TV to the Joey and an HDMI cable from Joey to the TV. In the living room he ran a cable from the satellite wall jack to the Hopper and ran an HDMI cable from the Hopper to the TV. Everything works just as it did in the house in Kentucky. Tim
|
|
|
11-05-2015, 11:03 AM
|
#7
|
Montana Master
Join Date: Oct 2013
Location: Ogden
Posts: 638
M.O.C. #13862
|
Quote:
quote:Originally posted by tweber502
Just had this set-up installed in our 2010 3400RL. The service tech installed a triple LNB dish on a pole. He then attached a solo NODE to the dish and ran a single coax cable from the NODE to our service center. He attached a TAP to the other end of the coax which splits the signal. We have 2 satellite and 1 cable TV inputs in our service center. From the tap he ran a cable to each satellite connection, one to the HOST and one to CLIENT (on the tap), Host is the sat connection for the living room where the Hopper is and client is the one for the bedroom where Joey is. In the closet in bedroom he removed the jumper from the antenna booster and connected it to the satellite feed which completes the circuit to the bedroom TV. Connected the coax from the wall behind the TV to the Joey and an HDMI cable from Joey to the TV. In the living room he ran a cable from the satellite wall jack to the Hopper and ran an HDMI cable from the Hopper to the TV. Everything works just as it did in the house in Kentucky. Tim
|
Awesomely perfect, detailed description! Just exactly what I needed to move forward. I'm ordering a node and tap off of Amazon right now. Thanks again!
|
|
|
11-05-2015, 11:10 AM
|
#8
|
Montana Fan
Join Date: Aug 2013
Location: Springfield
Posts: 322
M.O.C. #13660
|
Mark, if you already have an account with Dish they should provide anything needed for the set-up for free. I opted to have an outside source that does Dish and Direct installs do my set-up because he was familiar to RV applications and has done several in the park we live in. His charge for set-up including everything needed except the Hopper and Joey which we already had was $65. This fee also includes relocation if we decide to change sites within the park. Dish was going to do the install for free but they did say they weren't that familiar with RV applications. Tim
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|