Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 

Go Back   Montana Owners Club - Keystone Montana 5th Wheel Forum > GENERAL DISCUSSIONS > General Discussions about our Montanas
Click Here to Login

Reply
 
Thread Tools Search this Thread Display Modes
 
Old 06-08-2013, 03:14 AM   #1
jlb27537
Montana Master
 
Join Date: Jan 2013
Location: Depends on temps
Posts: 1,648
M.O.C. #13157
2014 Spring hangers

Hello Group, This issue is still in the figuring out stage so no correction has taken place. I post this only for information so others might look at their rigs.

I had Mor/Ryde X Factor braces installed by my selling dealer. I have had my rig about 3 weeks. I went to grease the wet bolts a couple days ago and found the 4 wet bolts that attached the braces would either not take grease or take it with way too much effort on the grease gun handle.

I crawled under it and discovered the outer flange of the spring hanger was bent inward on all 4 locations.

My rig has springs that are 1 3/4" wide and when you measure between the shackles at the LRE center support the distance is 1 13/16". This means the bushing in the end of the spring is 1/16" longer than the spring is wide. This provides 1/32" of clearance on each side of the spring when bolted up. OK, no problem.

Now the problem??? The spring hangers welded onto the frame when measured at the point of attachment is 2 1/16" wide. This would be the correct dimension for a 2" spring, but when you put a 1 3/4" wide spring in a 2" wide hanger and you have a X Factor brace in place it causes the outer flange, (which is 1/4" too wide) to bend inward when you tighten up the wet bolt.

I have measured, sent pictures to Mor/Ryde and have e mailed Keystone. Monday I'll call and see what the engineers @ Mor/Ryde have to say and will call Keystone for their take on the matter.

Mor/Ryde tells me he has never seen anything like this. It may be that Lippert somehow got the wrong info or Dexter provided the wrong springs. Like I said, this is still in the figuring out stage.

I'm not a engineer, but I feel a spring hanger that is bent is not a good thing.








 
__________________

2012 Ram Laramie 3500 DRW 4x4 3.73 Tow Max Pkg B&W Companion 60 gal RDS aux fuel tank. 2014 Montana 3150RL, 2 A/C's, Leather, 6 Point Jacks, Splendede WD2100XC, Mor/ryde X-Factor, Duravis 250 tires with TST 507RV monitors. 2 x Honda EU2000's
jlb27537 is offline   Reply With Quote
Old 06-08-2013, 03:44 AM   #2
Chip
Montana Fan
 
Join Date: Oct 2006
Location: Friendship, Maine
Posts: 483
M.O.C. #6338
I am surprised Mor/Ryde did not say something about it when they installed the brace.

This is interesting.

__________________

2012 Big Sky 3400, now an SOB 5th wheel
2007 Montana 3075 previously
2015 GMC 3500 Dually
Chip is offline   Reply With Quote
Old 06-08-2013, 04:00 AM   #3
1retired06
Montana Master
 
Join Date: Feb 2012
Location: Lake Gaston
Posts: 8,773
M.O.C. #12156
Not Good!
__________________
Mike and Lorraine
2002 3655 FL, 2005 3650RK
2010 3665RE, 2015 3910FB
F350 crew cab dually 6.7
1retired06 is offline   Reply With Quote
Old 06-08-2013, 04:04 AM   #4
jlb27537
Montana Master
 
Join Date: Jan 2013
Location: Depends on temps
Posts: 1,648
M.O.C. #13157
Quote:
quote:Originally posted by Chip

I am surprised Mor/Ryde did not say something about it when they installed the brace.

This is interesting.

Chip in my post I said my selling dealer installed them. Mor/Ryde did not install them. I am sure if Mor/Ryde did the install they would have caught the issue.
__________________

2012 Ram Laramie 3500 DRW 4x4 3.73 Tow Max Pkg B&W Companion 60 gal RDS aux fuel tank. 2014 Montana 3150RL, 2 A/C's, Leather, 6 Point Jacks, Splendede WD2100XC, Mor/ryde X-Factor, Duravis 250 tires with TST 507RV monitors. 2 x Honda EU2000's
jlb27537 is offline   Reply With Quote
Old 06-08-2013, 04:08 AM   #5
DQDick
Site Team
 
DQDick's Avatar
 
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
Glad you caught it, hard to figure how and why it happened in the first place.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
DQDick is offline   Reply With Quote
Old 06-08-2013, 04:13 AM   #6
Irlpguy
Montana Master
 
Join Date: Oct 2012
Location: Chilliwack
Posts: 1,520
M.O.C. #12935
Great pictures Jib27537 and yet another example of absolutely no QC right from the time the springs were put on the frame. Anyone with half a brain could see there was a problem and that is when the work should have stopped and the correct pieces put in.

Your selling dealer should never have put the X factor on those spring hangers, when they saw this they should have immediately informed you and stopped work. The wet bolts have been overtightened bending the hangers, albeit they are incorrect in my opinion. This might explain the difficulty in getting grease in the wet bolts.

There is a heck of a lot of not good things happening on your suspension, I would be concerned about the alignment of the axles as well and would be insisting on having that checked. The X factor has put additional stresses on the hanger rather than support it. Look at the third picture down in your post, terrible, just terrible. I would not tow this down the road until it was fixed.

Please keep us informed.
Irlpguy is offline   Reply With Quote
Old 06-08-2013, 04:44 AM   #7
Sheepdog
Montana Fan
 
Join Date: Apr 2010
Location: Kettle Falls
Posts: 363
M.O.C. #10354
Those black rubber Marabombs in the picture are also a problem you need to address!
Sheepdog is offline   Reply With Quote
Old 06-08-2013, 04:47 AM   #8
Irlpguy
Montana Master
 
Join Date: Oct 2012
Location: Chilliwack
Posts: 1,520
M.O.C. #12935
I was curious and went and measured my springs and hangers, I have 1 3/4" springs and my hangers measure 1 7/8" both at the top and bottom of the hanger, this gives the spring a 1/16th theoretical space on either side of the hanger for movement. I still had to remove 3 wet bolts and reinstall them to be able to grease them. All zerks were loose, three were missing altogether and I replaced all with 90 degree ones for ease of greasing.

Your selling dealer appears to do much the same kind of work as the one where I bought mine, poor workmanship follows all the way down the line. There is no way I would ever again have either yours or my dealer work on my RV.
Irlpguy is offline   Reply With Quote
Old 06-08-2013, 07:50 AM   #9
jlb27537
Montana Master
 
Join Date: Jan 2013
Location: Depends on temps
Posts: 1,648
M.O.C. #13157
Quote:
quote:Originally posted by Sheepdog

Those black rubber Marabombs in the picture are also a problem you need to address!
Yes I am aware of that. Wife says I need to wait a month or so to get over the sales tax on a new truck and trailer. The spring thing is on top of the list right now. I towed it from Indiana to Michigan to Missouri so it has about 7-800 miles with the hangers like this so I am not worried about the safety issue.

My thought is remove the current wet bolts, using a all thread rod, push the outer hanger arm back out, (or bend it back out with a large crescent wrench)re-install the springs with a 1/8" washer/spacer on each side of the spring to make up for the 1/4" too wide hanger, install longer wet bolts and you are done.

Pic 3 does look like the hanger is rolled under but it is not, just the outer leg of the bracket is pulled in.

If I had not had the braces installed, I probably would have never noticed I had 2" brackets on a 1 3/4" spring.

Jim
__________________

2012 Ram Laramie 3500 DRW 4x4 3.73 Tow Max Pkg B&W Companion 60 gal RDS aux fuel tank. 2014 Montana 3150RL, 2 A/C's, Leather, 6 Point Jacks, Splendede WD2100XC, Mor/ryde X-Factor, Duravis 250 tires with TST 507RV monitors. 2 x Honda EU2000's
jlb27537 is offline   Reply With Quote
Old 06-08-2013, 08:30 AM   #10
Irlpguy
Montana Master
 
Join Date: Oct 2012
Location: Chilliwack
Posts: 1,520
M.O.C. #12935
Jim I would caution you against doing anything yourself to solve this problem, that will do nothing but give those responsible the excuse to not warranty this problem. You have a brand new unit there, it should be repaired correctly under warranty.

I am certain the hangers and wet bolts are all part of what Dexter ship to either Keystone or Lippert to have mounted on the frame, they were wrong from the get go and I would be contacting Dexter as well as Keystone & Lippert. There will likely be a lot of buck passing going on, however for your sake I hope someone steps up to the plate and does the right thing. My guess would be they are installed at the Keystone factory, but very well may have been shipped with the wrong hangers from Dexter in the first place.

If that were my unit I would be insisting the wrong size hangers be cut off and replaced with the correct ones, I would insist the alignment be checked during this process or upon completion, do not settle for less than what it should be. If your alignment is out it will ruin any tire you have on the RV.

IMHO the "Marabombs" would be the least of my worries, contrary to popular opinion on this forum I have had no problem with mine and have over 8000 miles on them. When we purchase one of these very expensive RV's it should not become a money pit to make it right, unfortunately that seems to be a common necessity with Montana owners.
Irlpguy is offline   Reply With Quote
Old 06-09-2013, 01:53 AM   #11
jlb27537
Montana Master
 
Join Date: Jan 2013
Location: Depends on temps
Posts: 1,648
M.O.C. #13157
Hi Ed,

I am not sure who installs the spring hangers, but will know Monday. The engineers @ Mor/Ryde have been aware of this for a week. I'll call my contact there Monday for a update. If they are no where, I'm on the phone to Keystone. I E-mailed them last week.

I have no intention of fixing this my self. I will have it done. Cutting off the brackets may cause more harm than good. It may be just as easy to just shim, use spacers, longer wet bolts to keep everything square. Yes, a alignment would be in order after all this.
__________________

2012 Ram Laramie 3500 DRW 4x4 3.73 Tow Max Pkg B&W Companion 60 gal RDS aux fuel tank. 2014 Montana 3150RL, 2 A/C's, Leather, 6 Point Jacks, Splendede WD2100XC, Mor/ryde X-Factor, Duravis 250 tires with TST 507RV monitors. 2 x Honda EU2000's
jlb27537 is offline   Reply With Quote
Old 06-09-2013, 11:09 AM   #12
richfaa
Montana Master
 
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
Hold Keystone feet to the fire..This crap has got to stop.
richfaa is offline   Reply With Quote
Old 06-29-2013, 03:38 AM   #13
gregh9999
Established Member
 
Join Date: Jul 2008
Location: Richmond
Posts: 48
M.O.C. #8671
My 2013 3100 (new design) has the same problem stock from the factory. My hangers are bent in to meet the springs.
gregh9999 is offline   Reply With Quote
Old 06-29-2013, 05:03 AM   #14
Sierra 117
Montana Fan
 
Join Date: Jul 2009
Location: Stratford
Posts: 241
M.O.C. #9481
Mor/Ryde specs call for only a 50 pd/ft torque on the spring eye bolt, not enough to bend the hanger.
Sierra 117 is offline   Reply With Quote
Old 06-30-2013, 04:10 AM   #15
jlb27537
Montana Master
 
Join Date: Jan 2013
Location: Depends on temps
Posts: 1,648
M.O.C. #13157
Nope, not so. The wet bolt is shouldered and 50lbs will pull the hanger in till the bolt bottoms out. A wet bolt is not shaped like a regular bolt. Go get a wet bolt and look at it.

Jim
__________________

2012 Ram Laramie 3500 DRW 4x4 3.73 Tow Max Pkg B&W Companion 60 gal RDS aux fuel tank. 2014 Montana 3150RL, 2 A/C's, Leather, 6 Point Jacks, Splendede WD2100XC, Mor/ryde X-Factor, Duravis 250 tires with TST 507RV monitors. 2 x Honda EU2000's
jlb27537 is offline   Reply With Quote
Old 06-30-2013, 04:56 AM   #16
RJI47
Montana Fan
 
Join Date: Jul 2006
Location: No. Attleboro
Posts: 338
M.O.C. #6002
Send a message via AIM to RJI47 Send a message via Yahoo to RJI47
I'm surprised the dealer that installed the wet bolts didn't notice the problem. Or maybe they did, but just neglected to mention it to you.
RJI47 is offline   Reply With Quote
Old 06-30-2013, 04:57 AM   #17
Tom S.
Montana Master
 
Join Date: Aug 2007
Location: Waterford
Posts: 3,693
M.O.C. #7500
Quote:
quote:Originally posted by jlb27537

Nope, not so. The wet bolt is shouldered and 50lbs will pull the hanger in till the bolt bottoms out. A wet bolt is not shaped like a regular bolt. Go get a wet bolt and look at it.

Jim
And that is what is troubling me. Since the bolt is shouldered, how could they have collapsed the hangers that far, unless the bolts were the wrong ones, or the shoulder was cut too far back.
Tom S. is offline   Reply With Quote
Old 06-30-2013, 05:28 AM   #18
jlb27537
Montana Master
 
Join Date: Jan 2013
Location: Depends on temps
Posts: 1,648
M.O.C. #13157
The wet bolt comes in different lengths. They are sized for spring width and hanger width. Dexter provides the wet bolts.

Dexter specs the hangers @ 1.82-1.94" wide inside. Lippert installed hangers that are 2.059-2.062" wide inside.

So if the hanger is 1/4" too wide, the bolt, when tightened, will cause the hanger to bend inward when the inner hanger is held square to the spring and pivot bolt.

If you do not have X Factor braces the hangers will be pulled in about a 1/8" on each side and you probably will not notice it. Get your digital gauge and measure hanger width at point of attachment to the frame I beam.

This is not rocket science. The hangers are out of Dexter specs and neither Lippert or Keystone will accept responsibility.

Jim
__________________

2012 Ram Laramie 3500 DRW 4x4 3.73 Tow Max Pkg B&W Companion 60 gal RDS aux fuel tank. 2014 Montana 3150RL, 2 A/C's, Leather, 6 Point Jacks, Splendede WD2100XC, Mor/ryde X-Factor, Duravis 250 tires with TST 507RV monitors. 2 x Honda EU2000's
jlb27537 is offline   Reply With Quote
Old 07-02-2013, 07:54 AM   #19
richfaa
Montana Master
 
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
Was under the Rig doing slide maint and took a look at the spring hangers. Mine are bent a tiny bit but nothing like what you show. The axle and spring assembly come into the plant fully assembled so Keystone installs them in the hangers. As I recall that happens at the first or second assembly station.
richfaa is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tires and Spring Hangers steves TIRES, Montana Tires 22 09-22-2013 09:38 AM
More Ryde Spring hangers Rick Repairs & Service 1 10-21-2011 04:11 AM
Spring Hangers pineranch Additions & Improvements 2 01-24-2011 07:20 AM
Spring Hangers on 3295RK 2007 Jerry Smith Maintenance 18 04-18-2010 02:27 AM
Awning hangers Steve and Brenda General Discussions about our Montanas 10 05-23-2007 04:54 AM

» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.


All times are GMT -6. The time now is 04:23 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.