|
05-05-2012, 07:27 AM
|
#1
|
Montana Fan
Join Date: Jul 2011
Location: Farmington
Posts: 283
M.O.C. #11619
|
Roof bubble
I was up top putting my cover on and noticed this bubble in the roof material along the side edge.
http://youtu.be/QHOi1VIZPbI
Is this something to worry about?
|
|
|
05-05-2012, 09:32 AM
|
#2
|
Montana Master
Join Date: Apr 2006
Location: Mesa az
Posts: 2,952
M.O.C. #5651
|
Not sure if problem or not. But I have the same thing on mine (maybe not quite so big). I took pictures and sent them to Keystone near the end of the trailer warranty so there would be proof if things got worse.
But things have stayed the same so far - now almost 6 years.
Good luck.
__________________
Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
|
|
|
05-05-2012, 10:47 AM
|
#3
|
Montana Fan
Join Date: Jul 2011
Location: Farmington
Posts: 283
M.O.C. #11619
|
Quote:
quote:Originally posted by twindman
Not sure if problem or not. But I have the same thing on mine (maybe not quite so big). I took pictures and sent them to Keystone near the end of the trailer warranty so there would be proof if things got worse.
But things have stayed the same so far - now almost 6 years.
Good luck.
|
I sent the link to Keystone's service/parts/support via their website contact form.
|
|
|
05-05-2012, 11:13 AM
|
#4
|
Montana Master
Join Date: Jan 2012
Location: Copperas Cove
Posts: 1,426
M.O.C. #12096
|
Mine is the same way...
|
|
|
05-05-2012, 11:34 AM
|
#5
|
Montana Master
Join Date: Feb 2012
Location: Lake Gaston
Posts: 8,773
M.O.C. #12156
|
Your video taking too long for me to download. However, Small roof bubbles generally are not of concern, unless they get bigger.
__________________
Mike and Lorraine
2002 3655 FL, 2005 3650RK
2010 3665RE, 2015 3910FB
F350 crew cab dually 6.7
|
|
|
05-05-2012, 11:40 AM
|
#6
|
Montana Fan
Join Date: Jul 2011
Location: Farmington
Posts: 283
M.O.C. #11619
|
I have bubbles all over the roof and they don't really concern me. The part about this particular spot is that it is at the edge where the fiberglass side wraps under it. I'm able to push the fiberglass skin down in the bubble about 1/2 inch or so. I guess I'm wondering also if the fiberglass should be stuck to the roof under the rubber roof. The bubble runs about the length of my hand long, and about 2 or 3 fingers wide.
|
|
|
05-05-2012, 11:44 AM
|
#7
|
Montana Master
Join Date: Dec 2006
Location: corning
Posts: 694
M.O.C. #6635
|
Looks fairly common to me. I'd keep an eye on it incase it starts to grow. I have a couple slightly smaller ones but they have not grown since nearly new.
Okay, just read your last post. I would get that fixed.
|
|
|
05-05-2012, 12:21 PM
|
#8
|
Montana Fan
Join Date: Jul 2011
Location: Farmington
Posts: 283
M.O.C. #11619
|
Quote:
quote:Originally posted by camper4
Looks fairly common to me. I'd keep an eye on it incase it starts to grow. I have a couple slightly smaller ones but they have not grown since nearly new.
Okay, just read your last post. I would get that fixed.
|
In the video the part I am pressing on is the fiberglass under the roof material.
|
|
|
05-05-2012, 01:40 PM
|
#9
|
Montana Master
Join Date: Dec 2006
Location: corning
Posts: 694
M.O.C. #6635
|
Yea, that might have a sharp edge that could wear a hole in the rubber. Should be looked at by someone who knows what they are doing.
|
|
|
05-07-2012, 02:18 AM
|
#10
|
Montana Master
Join Date: Jan 2005
Location: Goshen
Posts: 1,058
M.O.C. #2827
|
bighornram, I don't think that is fiberglass under the rubber. Unless Keystone has changed, that is radiused aluminum that goes up around the corner from the gelcoat to the roof decking. Then, the rubber is glued over it.
Our old Challenger has had roof bubbles ever since it was new 7 years ago. They generally run cross wise from side-to-side about every 4 feet where the 4X8' sheets butt together. In all these years, they have never changed or gotten any bigger. The first couple years, I was concerned about it but, have gained experience in the RV industry enough to know that it generally is not a problem.
What is a problem is when the glue is not applied to the decking in the correct amount before the rubber is layed on it and rolled. There is also the possiblity of too much glue being applied in which case, it does not set-up properly.
|
|
|
05-07-2012, 10:08 AM
|
#11
|
Montana Fan
Join Date: Apr 2011
Location: Baton Rouge
Posts: 431
M.O.C. #11342
|
This is what the owner's guide has to say about the rubber roof:
Roof
In most cases, the roof assembly consists of the interior paneling, a truss system, insulation, roof decking (plywood, OSB) and a rubber roof which is glued to the roof decking. Because of the manufacturing process, air pockets and/or visible spots may be seen in the rubber roof. These visible spots can be caused by debris (wood, staples, screws, etc.) that are between the rubber roof and decking or by imperfections occurring during the rubber roof manufacturer. In most cases, these are considered cosmetic in nature and seldom require any corrective action.
Rubber Roof
The rubber roof is a polymer membrane that will not rust or corrode and is very strong and durable. Other than periodic washing, the rubber roof material itself does not require maintenance or coatings. However, be advised that any attachment, seams or joints in the rubber roof requires maintenance often!
The roof material can, however, be punctured, snagged or cut by contact from other objects. Know the height of your unit and avoid contact with overpasses, trees, etc. If the rubber roof is damaged, it is designed to be patched. “Rubber roof
|
|
|
05-09-2012, 11:24 AM
|
#12
|
Montana Master
Join Date: Feb 2004
Location: New Braunfels
Posts: 664
M.O.C. #920
|
I think the radius aluminum mentioned by MIMF2 is held in place with screws. If the aluminum is flexing, it is due to not enough screws or a screw has come loose. The rubber roof is not glued to the aluminum or it was not on mine when the roof was replaced. I would watch for the head of a screw protruding up from under the roof.
|
|
|
05-18-2012, 07:49 PM
|
#13
|
Established Member
Join Date: Apr 2012
Location: Carson
Posts: 10
M.O.C. #12378
|
There is a difference between bubbles and lifting decking. I have 2 sections of decking that have lifted from the trusses. It looks like a bubble until you push down on it like you do on the video. Yours appears to be the same as mine...a decking problem. I noticed mine the first day that I took possession. I took it back to the dealership, Keystone authorized a replacement roof. I'm still waiting for the repair...it's been over a month.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Dicor Roof Bubble
|
Denfinger |
Montana Problems, Problem Solving & Technical Help |
3 |
09-08-2013 05:32 AM |
Bubble Levels
|
oldgeezor |
General Discussions about our Montanas |
27 |
12-21-2011 04:50 AM |
Bubble in roof
|
sfish |
Maintenance |
1 |
07-07-2011 03:20 PM |
rubber roof bubble
|
genecurp |
Montana Problems, Problem Solving & Technical Help |
7 |
03-27-2006 02:36 AM |
Roof Air Bubble
|
Montana_1450 |
Montana Problems, Problem Solving & Technical Help |
8 |
06-20-2005 05:26 AM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|