|
07-01-2008, 07:29 AM
|
#1
|
Seasoned Camper
Join Date: Aug 2007
Location:
Posts: 93
M.O.C. #7484
|
Landing gear question
While sitting around feeling sorry for myself and trying (?) to recuperate from sciatica/back injury, I thought of something that might be a "back saver" for us old guys. My Mountaineer has the standard landing gear with spring-loaded locking pins. Has anyone ever tried hooking a spring from the foot pad to the area above the landing gear, so that the spring would pull the leg up when you pull the pin? I realize there is not a lot of weight involved, but you are in a very bad position "back-wise", leaning over or down on your knees, to pull the pin and lift the leg at the same time. Anyone seen or done this to their fiver?
|
|
|
07-01-2008, 08:53 AM
|
#2
|
Montana Fan
Join Date: Jun 2008
Location: Virginia Beach
Posts: 156
M.O.C. #8531
|
Nope, but in 10 minute tech book 3 there are a few suggestions to help make the process easier. One was to attach parts from bicycle handlebars: cut about 8" or more off each side, flatten the cut end, drill through the flattened part, then attach to the leg plates with self tapping screws. Be sure to leave the plastic/rubber caps on the ends of the handlebars. You can use a slightly longer length (remember the banana seat bikes with the long U shaped handlebars?) and then you don't have to bend over quite so much. This helps avoid trying to push up and allows you to pull up--much better on the back. However, check your turning clearance before adding to much length.
Another suggestion was to attach a piece of iron to the peg which holds the spring clip. Cut it so when it is installed it is just short of the exact length as the pin is when extended. You'll anchor the pin head on this piece of metal (twist the pin) until you've moved the leg plates to the desired position. A simple tap will release the spring pin and then it locks the leg into place.
|
|
|
07-01-2008, 02:44 PM
|
#3
|
Montana Master
Join Date: May 2003
Location: New Bern
Posts: 4,294
M.O.C. #311
|
The problem I see with the springs is putting the extension down when you set up.
One thought I have is putting a pully up top on the frame with a rope to the foot letting you pull it up. What you do with the rope when in transport has not been thought through.
Good luck.
|
|
|
07-01-2008, 03:07 PM
|
#4
|
Montana Master
Join Date: Oct 2007
Location: Land O Lakes
Posts: 2,751
M.O.C. #7753
|
When I installed my JTs I noticed that the holes in the inner leg were pointing fore and aft instead of side to side. I was going to change them but my buddy said leave them the way they are because that would give me a handle in front instead of on the side. So that's what I did and it worked out great. It is easy to reach and I am pulling almost straight up as opposed to up and out. Dave and Betsy
|
|
|
07-01-2008, 03:08 PM
|
#5
|
Montana Master
Join Date: Sep 2003
Location: Sunshine
Posts: 1,445
M.O.C. #538
|
I use a wife. I did install a 3/8" bolt about 5" long in to the bottom hole of the landing gear. This acts as a handle.
|
|
|
07-01-2008, 05:33 PM
|
#6
|
Montana Master
Join Date: Sep 2007
Location: Texas City
Posts: 5,736
M.O.C. #7673
|
Wife works for me! She has to have some duties besides cooking, laundry, walking the dog, and nagging!
Edited: It's her fault she does not get on here and read the forum - and my fortune.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|