|
03-27-2007, 04:45 AM
|
#1
|
Montana Master
Join Date: Dec 2006
Location:
Posts: 2,376
M.O.C. #6575
|
Wiring for inverter
We purchased a 3.2 cubic foot upright freezer for the fiver. I have a 500 watt (1000 watt surge) inverter that I want to run it on while on the road. Here is what I have calculated. The freezer draws almost 2 amps or around 240 watts. It will approximately double that on start up. The inverter will draw about 10 amps on the dc side for every 100 watts output. I plan to run the wire from the terminal block above the battery back to the kitchen cabinets. From what I can find on line, #8 wire will carry the current, but with the length (around 25 feet) I will be running, I am thinking maybe #6 wire. Any input appreciated.
|
|
|
03-27-2007, 05:04 AM
|
#2
|
Montana Master
Join Date: Aug 2004
Location: Cedar Rapids
Posts: 4,876
M.O.C. #1944
|
#8 wire will more than suffice. According to AWG website, the current rating for copper wire, #8, is 40 amps.
Orv
|
|
|
03-27-2007, 05:20 AM
|
#3
|
Montana Master
Join Date: Jul 2006
Location: K.C.
Posts: 11,731
M.O.C. #5980
|
I would go with a larger inverter, the start up amps can go as high as 7 times run for a millisecond...depends on the compressor and start assist, if any it has.
I doubt the small one will work. If you have it now, give it a few trys on the old 'bench test'.
Good luck.
Ozz
|
|
|
03-27-2007, 12:58 PM
|
#4
|
Montana Master
Join Date: Jul 2004
Location: Conover
Posts: 995
M.O.C. #1832
|
You will need 2000 watt inverter to work properly and handle the loads, with a 500 watt you will either trip breaker or circuit if you put one in line or you will burn it up one of the two, agree with Ozz not big enough.
Try this web site will http://www.theinverterstore.com/?gcl...FQfxgAodIDhHRg give you tons of info on them plus help you size for what you are doing.
|
|
|
03-27-2007, 01:17 PM
|
#5
|
Montana Master
Join Date: May 2006
Location: Ronan
Posts: 513
M.O.C. #5756
|
I'm with Ozz bigger wire is the only way to carry the load also would suggest a transfer switch for when outside power is hooked up I hooked my inverter right through the fuse box to power the 110 plugs I wanted power to works like a charm for my purposes good luck
|
|
|
03-27-2007, 03:20 PM
|
#6
|
Montana Master
Join Date: Dec 2006
Location:
Posts: 2,376
M.O.C. #6575
|
I am going to wait until I hit the home base and test the freezer then. I am only going to use the inverter strictly for the freezer while on the road. Why would I need a transfer switch, as I will merely plug the freezer into the inverter when we hit the road? Am I missing something there? Thanks for the input.
|
|
|
03-27-2007, 03:45 PM
|
#7
|
Montana Master
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
|
Will.. FYI..We have a 3.2 cu ft freezer (Haier) sits in the rear of our 3400 in place of one of the recliners. We keep it at @ Zero degrees. When on the road it remains without power , We have run more than 8 hours and it has warmed only 3 or 4 degrees.You might want to do some testing before spending a lot of money.
|
|
|
03-27-2007, 03:52 PM
|
#8
|
Montana Master
Join Date: Oct 2006
Location: Choctaw
Posts: 530
M.O.C. #6364
|
Wow, this is the classic Edison versus Westinghouse question. The best answer would be to keep the inverter close to the DC power source using a sufficient size wire for the power and then run a 12AWG AC line to the load, in this case the freezer.
Wire length equals current loss in DC circuits. Remember at the turn of the last century AC and DC current went head to head and thankfully AC won or we'd all have to live within a mile of a power generating station just to have sufficient current to run a TV set.
|
|
|
03-27-2007, 04:23 PM
|
#9
|
Montana Master
Join Date: Dec 2006
Location:
Posts: 2,376
M.O.C. #6575
|
Quote:
quote:Originally posted by Steve and Brenda
Wow, this is the classic Edison versus Westinghouse question. The best answer would be to keep the inverter close to the DC power source using a sufficient size wire for the power and then run a 12AWG AC line to the load, in this case the freezer.
Wire length equals current loss in DC circuits. Remember at the turn of the last century AC and DC current went head to head and thankfully AC won or we'd all have to live within a mile of a power generating station just to have sufficient current to run a TV set.
|
You make a very valid point. I suppose I could just add another plug in the cabinet. Also, Rich may have the best idea, just close it and leave it alone, unless we decide to boondock a little. You guys are great. That's exactly why I posted. Thanks so much.
|
|
|
03-27-2007, 06:22 PM
|
#10
|
Montana Master
Join Date: Aug 2006
Location: Lone Tree
Posts: 5,615
M.O.C. #6109
|
Quote:
quote:Originally posted by Steve and Brenda
Wow, this is the classic Edison versus Westinghouse question.
|
hahaha- great comment Steve! Not sure I would have understood it except I just read the history about it in book a few weeks back.
|
|
|
03-28-2007, 03:06 PM
|
#11
|
Montana Master
Join Date: Oct 2006
Location: Choctaw
Posts: 530
M.O.C. #6364
|
Quote:
quote:Originally posted by bsmeaton
Quote:
quote:Originally posted by Steve and Brenda
Wow, this is the classic Edison versus Westinghouse question.
|
hahaha- great comment Steve! Not sure I would have understood it except I just read the history about it in book a few weeks back.
|
Brad, glad you understood. AC versus DC is basic study in the Electronics discipline. You know, most applications use DC still, we just convert the AC to DC INSIDE the device because AC is so easy to move along a power grid.
Willie, what is stopping you from moving to a bigger setup where you can power the entire power grid inside the vehicle with an inverter? You'd have the best of both worlds while traveling. Your batteries would not deplete as long as the TV is running and you have a sufficiently large bank of cells plus you could use the microwave at a rest area!!! Remember the transfer switch - important device when connecting to shore power.
|
|
|
03-28-2007, 05:00 PM
|
#12
|
Montana Master
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
|
When we boondock, such as it is, and that has amounted to about 24 hours in Quartzsite, we hook up the old Kipor 3500, crank up the TV, DVD, all the goodies including the freezer..and rough it.
|
|
|
03-28-2007, 07:48 PM
|
#13
|
Montana Master
Join Date: Sep 2006
Location: Casa Grande
Posts: 5,369
M.O.C. #6333
|
Anyone know a good website where I can study up on inverters??? I don't think my '06 3400 has one and would like to explore the possibilities. Also solar energy......
|
|
|
03-29-2007, 02:50 AM
|
#14
|
Montana Master
Join Date: Jul 2006
Location: K.C.
Posts: 11,731
M.O.C. #5980
|
Look up 'The 12 volt side of life', parts one and two.
I think Glenn has some refrences posted in the home location deal somewhere.
|
|
|
03-29-2007, 01:25 PM
|
#15
|
Montana Master
Join Date: Nov 2005
Location: Campbell River
Posts: 970
M.O.C. #4976
|
Hi Phil,
I put a 1200watt Xantrex in, and it runs everything I want it to. ( not always at the same time)
even the drip coffee pot. I put it by the laundry chute.. I don't have to go outside to turn it on & off, and I didn't
need more then the 5' of battery cable they recommend (no longer).
It was also easy to run a extension cord to the entertainment unit in our 2980RL
Heres a website & some pictures.
http://www.xantrex.com/
|
|
|
03-29-2007, 06:59 PM
|
#16
|
Montana Fan
Join Date: Feb 2006
Location: Lawrenceville
Posts: 279
M.O.C. #5356
|
Ok i cheated. Had to break out the ole engineering quick calcualtor i had from the telephone power days. Number 8 AWG (16,510 cm) will carry the load fine. At 25 feet using 8 AWG the voltage drop will be on the order of .17 Volts.
|
|
|
03-30-2007, 02:28 PM
|
#17
|
Montana Master
Join Date: Oct 2006
Location: Choctaw
Posts: 530
M.O.C. #6364
|
In this case current drop is a bigger factor but 8 AWG line feed on a DC circuit is certainly heavier and harder to manage as compared to using 12 AWG load feed from the inverter.
|
|
|
03-30-2007, 05:29 PM
|
#18
|
Montana Master
Join Date: May 2006
Location: Ronan
Posts: 513
M.O.C. #5756
|
I went to the camping world web site and typed in inverter and found out alot of info I bought the Xantrex 1800 watt with a auto transfer switch built in hooked it up right behind my batts. and ran a remote on and off switch the the cabin right above my tank monitor panel then ran nomex to the circut breaker panel to power the 110 plugs I wanted to use and it works flawless great for those mornings and evenings I want to watch the sat tv without running the gen as to not bother others camping around us we do alot of boondocking so its the perfect fit I also installed 6 12 volt batts. spliting them to two banks useing a batt. A/B switch so I really don't have too much trouble with 12volt power next I will be looking at a solor charger but for now I just run the gen to charge back up
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Inverter
|
JimnJulie |
General Discussions about our Montanas |
9 |
04-07-2015 05:29 AM |
Inverter
|
jimmy2 |
General Discussions about our Montanas |
18 |
10-09-2012 03:50 AM |
inverter
|
gregg-bean |
General Discussions about our Montanas |
4 |
10-27-2010 01:38 AM |
Wiring new style slide switch to old wiring?
|
danandbetty |
Montana Problems, Problem Solving & Technical Help |
4 |
06-30-2010 08:19 AM |
Inverter
|
Capt Kidd |
Montana Problems, Problem Solving & Technical Help |
7 |
07-04-2009 06:05 AM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|