Go Back   Montana Owners Club - Keystone Montana 5th Wheel Forum > GENERAL DISCUSSIONS > General Discussions about our Montanas
Click Here to Login

Thread Tools Display Modes
Old 07-20-2013, 05:45 AM   #1
Montana Master
Join Date: Feb 2007
Location: Winfield
Posts: 7,327
M.O.C. #6846
Need some HELP on programming TST sensors!

I am getting ready to install the four sensors on the TV dually tires and cannot find the instructions. Can someone please provide a brief recap of the programming steps to install additional sensors. Worst case if I have to re-install all sensors those initial instructions would be appreciated as well. Leaving Tuesday for the beach and Mid-Atl rally and am hoping to get the sensors installed today or tomorrow.

Bingo and Cathy - Our adventures begin in the hills of WV. We are blessed by our 2014 3850FL Big Sky (previous 2011 3750FL and 2007 3400RL) that we pull with a 2007 Chevy Silverado Classic DRW CC dually.
bncinwv is offline   Reply With Quote
Old 07-20-2013, 05:58 AM   #2
H. John Kohl
Montana Master
Join Date: May 2003
Location: Full Time
Posts: 4,260
M.O.C. #311
Send a message via AIM to H. John Kohl Send a message via MSN to H. John Kohl Send a message via Yahoo to H. John Kohl
H. John Kohl is offline   Reply With Quote
Old 07-20-2013, 09:16 AM   #3
Montana Master
Join Date: Aug 2008
Location: Shelburne
Posts: 688
M.O.C. #8693
Send a message via MSN to KathyandDave
We have the system and that's very accurate about how to set up one sensor. I would add that, when installing a lot of them, the hard part is keeping track of which code matches which tire. After messing it up a couple of times, I drew a little map of the tires, including the spares, then walked around the rig with a pocketful of sensors (a dozen). At each tire, I pulled out a sensor, recorded its four-character code on the map, then left the sensor by the tire. Then, I sat with the monitor and the map to do all the number entry and setup demonstrated in the video. Then, I walked around with the monitor and screwed the sensors on the stems one by one and watched the monitor find them one by one.
A clue for non-geeks: the number/letter code is called "hex", having sixteen "characters" in the following order: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F. On the monitor, "+" and "-" will move your selection forward and backward in the order.
On another thread, I mentioned that I've had a fantastic service experience with TST.
KathyandDave is offline   Reply With Quote
Old 07-20-2013, 09:37 AM   #4
Montana Master
DQDick's Avatar
Join Date: Jun 2011
Location: Wilsey
Posts: 17,258
M.O.C. #11455
Here's a link to the user manual for the model I have: http://www.greatrvproducts.com/uploa...ser_manual.pdf
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, MorRyde pin box
2017 3500 Dodge Maxi DRW 4X4, Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, etc.
DQDick is offline   Reply With Quote
Old 07-20-2013, 10:38 AM   #5
Montana Master
Join Date: Feb 2007
Location: Winfield
Posts: 7,327
M.O.C. #6846
Exactly what I needed, the MOC comes through again. I will download and save the pdf Dick gave the link to for the next time!!
bncinwv is offline   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Dish Programming?? timandsusan Let Us Entertain You 7 08-14-2015 03:50 PM
Tank Sensors dasmoeturhead Maintenance 24 12-09-2014 12:54 PM
Garmin GPS programming waypoints for rest areas Old_Salty Navigation 1 04-17-2012 06:02 AM
Key FOB Programming (2009 Montana ) exploringspace Montana Problems, Problem Solving & Technical Help 1 07-24-2009 09:47 AM
Local Programming ols1932 Let Us Entertain You 32 10-18-2008 12:43 PM

Powered by vBadvanced CMPS v3.2.3

This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.

All times are GMT -6. The time now is 04:17 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.