|
12-30-2006, 09:30 AM
|
#1
|
Established Member
Join Date: Nov 2004
Location: Anniston
Posts: 20
M.O.C. #2492
|
Propane Tanks
I have a 2002 Montana 3255RL, and my question is with my two 30 lb propane tanks.
When I use the right tank until it is completely empty, then switch to the left tank, I am not getting any gas at all from the full left tank.
I tried installing a new regulator, but the problem is still there.
I can physically move the left tank to the right side and it works perfectly, so I know there is nothing wrong with the cylinder itself.
Has anyone ever had this problem?
Please let me know of any solutions.
Thank You.
|
|
|
12-30-2006, 11:24 AM
|
#2
|
Montana Master
Join Date: Oct 2006
Location: _
Posts: 5,238
M.O.C. #6337
|
|
|
|
12-30-2006, 11:29 AM
|
#3
|
Montana Master
Join Date: May 2005
Location: Lake George
Posts: 1,078
M.O.C. #3847
|
Have you flipped over the tank selector valve?
|
|
|
12-30-2006, 11:33 AM
|
#4
|
Montana Master
Join Date: May 2003
Location: New Bern
Posts: 4,294
M.O.C. #311
|
The answer is yes. Now you need to see if the internal safety valve on the left tank has activated.
I had to open the top valve very slowly to prevent the tank internal safety valve from tripping.
Disconnect your left tank and slowly open the top valve and see if any propane comes out. If it does not, take it out, put some wood on the ground pick it up about a foot and drop it on the wood. Check and see if the propane will seep out now when you crack the valve (remember only crack it because the internal safety valve will shut down flow). If not pick it up a little higher and drop on the wood again. You are trying to reset the safety valve inside to allow flow. Once you have flow you can put it on either side. If you do put it on the left side just open the valve real slow so the tank does not think it is an open unsealed line.
I hope this helps.
Happy New Year.
|
|
|
12-30-2006, 01:39 PM
|
#5
|
Montana Master
Join Date: Aug 2004
Location: Cedar Rapids
Posts: 4,876
M.O.C. #1944
|
H. John Kohl is right. I don't know why, but the new valves do sometimes stick. Start with both valves turned off. Then, it is important that when you turn the valve open for use that you open it just a crack and then slowly open it all the way. Open both of them this way. Usually this solves the problem. Be sure you have the indicator pointing toward the tank that you want to draw from and that both tanks are open. This will allow you to draw from one tank until empty and then automatically switch to the full tank. Then switch the indicator to point to the full tank. Now you can remove the empty tank and get it refilled.
Orv
|
|
|
12-30-2006, 02:02 PM
|
#6
|
Established Member
Join Date: Nov 2004
Location: Anniston
Posts: 20
M.O.C. #2492
|
I don't think it is the internal safety valve on the tank itself, since I can move the full tank from the left side over to the right side, and it works there.
The full tank will not work when it is located in the left side compartment.
I thought at first it was just a bad regulator, but I replaced it with a new one.
GP
|
|
|
12-30-2006, 03:06 PM
|
#7
|
Established Member
Join Date: Nov 2004
Location: Anniston
Posts: 20
M.O.C. #2492
|
This is probably a stupid question, but if I have both tanks open at the same time, how do I know when one is empty, and when to turn the regulator handle to point to the full one.
Would the regulator indicator show red even after it automatically switches to the full tank?
Thanks.
|
|
|
12-30-2006, 03:19 PM
|
#8
|
Montana Master
Join Date: Nov 2003
Location: Layton
Posts: 1,048
M.O.C. #666
|
Around page 5-2 in your Montana manual talks about this condition, although kind of cryptic.
|
|
|
12-30-2006, 03:26 PM
|
#9
|
Montana Master
Join Date: Jan 2003
Location: Haldimand County
Posts: 2,413
M.O.C. #122
|
First, I think there are two things that may stick, one is the overfill protection device, and that is what banging on the ground may fix. Usually this is a problem encountered when filling the tank. The second is an excess flow valve that is located in the connector, this closes if the valve senses too much flow, and assumes that this is the result of a leak. This valve can be closed by the sudden surge of gas into the cross over pipe when you open the tank on the side opposite the regulator (the regulators are not all on the same side). Newer units have a secondary regulator to prevent this problem, but before 05, there was no secondary regulator (it is a red regulator located on the side away from the main regulator.)
The main regulator has an indicator that should show green when the in service tank has gas in it. When that tank runs empty, the indicator will turn red and the tank will automaticly swithch to the stand-by tank. You should check your regulator every few days to see it it has turned red, if it has, flip the lever over to the other side and your former stand by tank will become the in service tank, and you can remove the empty tank to refill it. When you put it back, open the valve very slowly, especially on the tank away from the main regulator, so that the excess flow valve will not close.
Long winded I know, but it is not as complicated in reality as it sounds in writing.
Good luck.
|
|
|
12-30-2006, 03:39 PM
|
#10
|
Montana Master
Join Date: Aug 2004
Location: Cedar Rapids
Posts: 4,876
M.O.C. #1944
|
Quote:
quote:Originally posted by gprice
This is probably a stupid question, but if I have both tanks open at the same time, how do I know when one is empty, and when to turn the regulator handle to point to the full one.
Would the regulator indicator show red even after it automatically switches to the full tank?
Thanks.
|
No question is ever stupid. You will know when one tank is empty by looking at your regulator. If the window shows red rather than green, the tank the indicator is pointing toward is empty. Flip the indicator lever toward the other tank. The regulator window will show green (assuming that tank is not empty also).
Orv
|
|
|
12-30-2006, 03:45 PM
|
#11
|
Established Member
Join Date: Nov 2004
Location: Anniston
Posts: 20
M.O.C. #2492
|
OntMont (John)
I understand that I can correct a stuck overfill protection device by dropping the tank onto a piece of wood. I guess this is to jar it loose. Is this dangerous?
Once it is stuck, how do I unstick the excess flow valve that is located in the connector?
Also, you said the newer models have a secondary regulator on the side opposite the main regulator.
Can I have one of these installed on my 2002 Montana?
Thank You
|
|
|
12-30-2006, 04:07 PM
|
#12
|
Montana Master
Join Date: Jan 2003
Location: Haldimand County
Posts: 2,413
M.O.C. #122
|
I learned it from an experienced propane guy. I don't think it would be dangerous (as long as you keep you foot out of the way).
On the second point, I forgot to say that the excess flow valves will reset themselves if you disconnect them to relieve the pressure on them, then re-connect, and SLOWLY open the tank valve.
I think it was October 2005 that the RVIA started to require the secondary regulator on RVs with the tanks in split locations. I imagine you could order one through any RV dealer, or possibly directly from the regulator manufacturer, Marshall Gas Regulator Co. I don't have one on my unit. I thought about getting one, but as long as you remember to open the tank valve slowly, they are not really necessary.
I hope this helps.
|
|
|
12-30-2006, 04:08 PM
|
#13
|
Montana Master
Join Date: Nov 2003
Location: Layton
Posts: 1,048
M.O.C. #666
|
I think this trail has been trod before.
If I recall correctly, with both tanks full and opened at the same time with the selection lever in the direction of the tank in use, the indicator will display as green. When tank empties, the indicator will indicate half green and half red. In this condition the regulator will switch to a reduced gas flow condition. When the tank selector switch is turned to the full tank the indicator will indicate green and the empty tank can be removed for filling.
Does this sound accurate?
|
|
|
12-30-2006, 04:47 PM
|
#14
|
Established Member
Join Date: Nov 2004
Location: Anniston
Posts: 20
M.O.C. #2492
|
John
From what you have said, it sounds like the excess flow valve.
I have always opened the valves quickly, but it only seems to cause a problem on the side oppisite the main regulator.
I will try this tomorrow to see if it corrects the problem.
Also, I would like to thank all the Montana folks who responded to my questions.
As always, You have been very kind & helpful.
GP
Alexandria, Alabama
|
|
|
01-01-2007, 03:27 PM
|
#15
|
Montana Fan
Join Date: Dec 2005
Location: moraga
Posts: 136
M.O.C. #5044
|
I wonder if it might just not be the big nut on the end of the hose that connects to the tank.
|
|
|
01-04-2007, 01:35 PM
|
#16
|
Established Member
Join Date: Nov 2004
Location: Anniston
Posts: 20
M.O.C. #2492
|
OntMont (John)
You were right John, I simply opened the valve very slowly, and it worked perfectly.
Thank You, and all the others who responded.
And yes, crandallbradley, after much trial & error, I did finally realize it "was" the big nut on the end of the hose.
|
|
|
01-06-2007, 05:09 PM
|
#17
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
I was not aware of the drop it on a board method. The two or three times we had this problem I just turned it upside down and back two or three times and it freed up.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
30 # vs 40 # propane tanks
|
lcarter |
Additions & Improvements |
20 |
11-11-2021 08:16 AM |
propane tanks
|
jenabby |
General Discussions about our Montanas |
4 |
07-30-2014 04:35 AM |
Propane Tanks
|
Jewels |
Montana Problems, Problem Solving & Technical Help |
22 |
12-12-2013 08:00 AM |
Propane Tanks
|
maximo |
General Discussions about our Montanas |
2 |
07-18-2011 07:51 AM |
1# Propane tanks
|
Ozz |
The Campsite |
6 |
05-16-2007 05:53 PM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|