|
02-10-2007, 04:48 AM
|
#1
|
Montana Master
Join Date: May 2006
Location: Oakland
Posts: 887
M.O.C. #5811
|
Potential water leak
I was installing pipe insulation to quiet the water lines when using the water pump and noticed a problem with the lines going to the shower. The lines go through metal ductwork and the holes in the metal are very ragged and sharp. To avoid having the lines rub and eventually leak, I am going to caulk around the holes.
Don
|
|
|
02-10-2007, 05:14 AM
|
#2
|
Montana Master
Join Date: Oct 2005
Location: Caldwell
Posts: 825
M.O.C. #4855
|
That doesn't look happy. Good idea about using caulk around them.
"Old world craftsmanship at it's finest"
|
|
|
02-10-2007, 05:21 AM
|
#3
|
Montana Master
Join Date: Oct 2003
Location: Malta
Posts: 3,075
M.O.C. #607
|
isn't there smaller pipe insulation you could use that is smaller that make fit in those holes?
|
|
|
02-10-2007, 05:41 AM
|
#4
|
Montana Master
Join Date: May 2006
Location: Oakland
Posts: 887
M.O.C. #5811
|
BillyRay The holes are sort of hacked out and not big enough to use pipe wrap, more and less than 3/8" clearance around the pipes.
Don
|
|
|
02-10-2007, 06:14 AM
|
#5
|
Montana Master
Join Date: May 2006
Location:
Posts: 1,733
M.O.C. #5751
|
Re those ragged holes, I've put a small piece of old garden hose around the hose I'm trying to protect and secured it with plastic ties.
|
|
|
02-10-2007, 09:45 AM
|
#6
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
good catch, Don. I think I can probably (hopefully) address this from inside the coach, in our rig, rather than dropping the bellypan.
|
|
|
02-10-2007, 12:08 PM
|
#7
|
Montana Master
Join Date: May 2006
Location: Oakland
Posts: 887
M.O.C. #5811
|
Steve,
You can get to the pipes from the basement area. Remove the access panel to the heater and you will see the pipes behind the heater going up to the shower. It will be a lot easier to see the pipes than reaching them, I had to climb inside the basement.
|
|
|
02-10-2007, 12:29 PM
|
#8
|
Montana Master
Join Date: Apr 2004
Location: Apple Valley
Posts: 1,574
M.O.C. #1358
|
They must've used a small hole saw for that - looks like a good spot for split grommets or plumbers putty?
Caulking may be a challenge with as much room as it has...might get the droopies...and require access from above and below.
|
|
|
02-10-2007, 03:39 PM
|
#9
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
Quote:
quote:Originally posted by nailbender
Steve,
You can get to the pipes from the basement area. Remove the access panel to the heater and you will see the pipes behind the heater going up to the shower. It will be a lot easier to see the pipes than reaching them, I had to climb inside the basement.
|
Thanks, Don. Now that you mention it, I do recall seeing pipes in that area when I removed that panel and crawled into the basement to address some loose connections causing water leaks. All three times, as a matter of fact. I didn't look closely at those lines, though, and don't specifically remember seeing those particular lines.
|
|
|
02-11-2007, 05:49 AM
|
#10
|
Montana Fan
Join Date: Sep 2006
Location: morgans point
Posts: 403
M.O.C. #6292
|
Thanks Don for the tip.
bob
|
|
|
02-19-2007, 01:43 PM
|
#11
|
Montana Master
Join Date: Jun 2003
Location: New Market
Posts: 831
M.O.C. #375
|
Wow Guys! I need to look inside of ours after seeing these horribly looking holes. I am sure the process has not improved. Does wrapping the exit lines from the water pump help reduce some of the noise? I've been thinking about putting in one of those quiet pumps but hate to cut loose the funds. If this will help, I'll give it a try.
|
|
|
02-19-2007, 01:59 PM
|
#12
|
Montana Master
Join Date: Dec 2004
Location: Bum F Egypt
Posts: 979
M.O.C. #2733
|
Boy that would have been a shame if they would have ran the line ether under or over the duct?SeeYa
|
|
|
02-19-2007, 03:31 PM
|
#13
|
Montana Master
Join Date: Feb 2006
Location: Driftwood
Posts: 1,376
M.O.C. #5446
|
Ok, here is an idea that I have..... Could you use the stuff that they use to fill in holes around windows and doors? I think it is called "Big Stuff" This is in a can and you spray it in an area that you want to seal and then it becomes hard. It comes out like a foam and then it hardens. You can spray it anywhere and it sticks to everything. Just a thought... has anyone else used this?
Colleen
|
|
|
02-19-2007, 04:02 PM
|
#14
|
Montana Master
Join Date: May 2006
Location: Oakland
Posts: 887
M.O.C. #5811
|
Native Tex, There are a lot of areas where the water lines touch the aluminum framing and I put the foam pipe insulation around the pipes to isolate them. Haven't tried it out yet, I blew the water out of the lines for the winter, but I sure it will make a difference. I didn't insulate all the lines completely, but still used about 16' of material.
Colleen, The foam spray would work, but would have to be very careful not get too much into the metal duck, some of the foams expand a lot.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Water leak
|
c214dick |
Repairs & Service |
7 |
10-13-2016 05:34 PM |
Water leak from seperated hot water line
|
rcreamo123 |
Full Timing in your Montana |
4 |
06-21-2010 12:00 PM |
Water leak from fresh water tank
|
grooving grandpa |
Montana Problems, Problem Solving & Technical Help |
4 |
04-23-2010 04:37 AM |
Water Leak
|
Korry J. Belin |
Montana Problems, Problem Solving & Technical Help |
7 |
09-12-2009 07:10 PM |
WATER LEAK!
|
Okie Guy |
Montana Problems, Problem Solving & Technical Help |
1 |
09-03-2007 10:15 AM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|