|
03-05-2024, 05:06 AM
|
#1
|
Montana Master
Join Date: Oct 2019
Location: Jacksonville
Posts: 2,183
M.O.C. #25165
|
Flushing the Water Heater
I was flushing the water heater and getting the rig winterized to go back to Elkhart yesterday and the hard plastic wand on my Camco water heater flush flew off and is now somewhere in the water heater tank. I've tried filling with water and floating it out, but that obviously isn't going to work. I put a camera inside the hole for the anode rod and I can't even see it anywhere to try and fish it out.
Should I be worried about it?
If so, How can I get it out? Any ideas?
__________________
Robert & Diana McNeal
2019 Montana Legacy 3791RD 20th Anniversary Edition
2014 F350 4x4 6.7L SRW
|
|
|
03-05-2024, 07:12 AM
|
#2
|
Montana Master
Join Date: May 2019
Location: Alton
Posts: 2,773
M.O.C. #24086
|
An endoscope camera with the hook attachment is your best bet.
I got this one. I've used it many times for various problems.
USB C Endoscope for OTG Android Phone, Computer, 5.5 mm Borescope Inspection Snake Camera Waterproof, 16.4 Ft Semi-Rigid Cord with 6 LED Lights, Compatible with Windows PC, MacBook https://a.co/d/9cFJ1q5
If you can't get it out, I wouldn't worry about it.
__________________
Daryl and Marianne,
2019 3130re 20th Anniversary Edition
2016 F350 Lariat
|
|
|
03-05-2024, 07:28 AM
|
#3
|
Montana Master
Join Date: Jun 2017
Location: POINTBLANK
Posts: 1,895
M.O.C. #19944
|
I'd be concerned it could melt around the electric heater element. As long as there is water it should not be a problem other than making it hard to remove at some point.
__________________
RAM 22' DRW 3500 Crew LB 40 gal reserve tank / RETRAX Bed Cover / 2020 373RD HC / IS / MOPEKA Tank Monitor / Furrion Side&Rear Cameras
Slide Toppers / EMS-HW50C / Sailun 85's
3rd AC / Dometic 320
|
|
|
03-05-2024, 07:58 AM
|
#4
|
Montana Master
Join Date: Oct 2019
Location: Jacksonville
Posts: 2,183
M.O.C. #25165
|
Quote:
Originally Posted by Daryles
An endoscope camera with the hook attachment is your best bet.
I got this one. I've used it many times for various problems.
USB C Endoscope for OTG Android Phone, Computer, 5.5 mm Borescope Inspection Snake Camera Waterproof, 16.4 Ft Semi-Rigid Cord with 6 LED Lights, Compatible with Windows PC, MacBook https://a.co/d/9cFJ1q5
If you can't get it out, I wouldn't worry about it.
|
I have a similar camera I bought on Amazon some time ago, but I cannot see it in there anywhere. I know it's in there, but I cannot see it.
I guess I'll just have to leave it for now.
__________________
Robert & Diana McNeal
2019 Montana Legacy 3791RD 20th Anniversary Edition
2014 F350 4x4 6.7L SRW
|
|
|
03-05-2024, 11:22 AM
|
#5
|
Montana Master
Join Date: May 2019
Location: Alton
Posts: 2,773
M.O.C. #24086
|
Quote:
Originally Posted by RMcNeal
I have a similar camera I bought on Amazon some time ago, but I cannot see it in there anywhere. I know it's in there, but I cannot see it.
I guess I'll just have to leave it for now.
|
Maybe it's against the wall (bottom corner) under the anode hole?
Try curving the camera back and looking where you go in at?
|
|
|
03-05-2024, 11:40 AM
|
#6
|
Site Team
Join Date: Apr 2017
Location: Colorado Rockies
Posts: 1,949
M.O.C. #19755
|
Maybe get another flushing attachment and run a bunch of water through the thing.
__________________
Scott & Alta
2017 Montana 3160RL, Legacy, Onan 5.5Kw, Solar
2022 F-450 Lariat Ultimate
|
|
|
03-05-2024, 12:01 PM
|
#7
|
Montana Master
Join Date: Oct 2018
Location: Anderson
Posts: 2,664
M.O.C. #22835
|
In your future, if you have an old washing machine hose, cut it in half and use that. No end to fly off. Works great! Been using several for over 25 years now. I keep giving them away. I'm down to my last 2 halves of the hose. (Fortunately).... I've not had to purchase any new washing machines in the last several years. But, those things work great!
__________________
History is not about the past, it's an explanation of the present.
2019 Montana High Country 375FL
2014 Chevy Silverado Duramax, 6.6L Dually
|
|
|
03-05-2024, 07:43 PM
|
#8
|
Site Team
Join Date: Aug 2007
Location: Omaha
Posts: 6,767
M.O.C. #7560
|
How about using one of the pickup or retrieval tools that you use to pick up bolts, nuts or anything dropped in a engine when working on them. They have a spring loaded end with four gripping prongs on the end that open up when you push on the button on the opposite end. I keep one in the Monte and have one in the in the shop incase I drop something while working in tight places. They have them at most hardware stores and also at Harbor Freight.
|
|
|
03-05-2024, 09:44 PM
|
#9
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,737
M.O.C. #12947
|
Quote:
Originally Posted by Daryles
Maybe it's against the wall (bottom corner) under the anode hole?
Try curving the camera back and looking where you go in at?
|
The tanks in these water heaters are cylindrical, not square walls and no corners. This is a photo of our old water heater that had leaked from a bad weld in the tank.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
03-06-2024, 05:02 AM
|
#10
|
Montana Master
Join Date: Oct 2019
Location: Jacksonville
Posts: 2,183
M.O.C. #25165
|
Thanks for the picture, Bob. That's what I thought. Even with the LED lights on the camera, I didn't see it in there. The way it shot off the end, I think it is probably lodged on the far side of the tank. When I get the rig back, I'll have more time (and hopefully more patience) to get back in there and locate it.
__________________
Robert & Diana McNeal
2019 Montana Legacy 3791RD 20th Anniversary Edition
2014 F350 4x4 6.7L SRW
|
|
|
03-10-2024, 01:31 PM
|
#11
|
Montana Master
Join Date: Jun 2018
Location: Folsom, California
Posts: 555
M.O.C. #21903
|
Quote:
Originally Posted by scottz
Maybe get another flushing attachment and run a bunch of water through the thing.
|
My plastic rinse end came off just like OP. After a few hours of trying to remove it, I gave up.
Bought a new rinser wand and next time I cleaned the tank. The old one appeared just inside the drain. Pulled it out with a needle nose.
It floats on the top of water, so leaving it in the tank isn't an issue as heating elements are low in the tank
Don't open the pressure release valve because rinser could get caught.
__________________
'05 F250 6.0 Bullet Proofed - Sold
'17 F350 6.7 Lariet
'02 Montana 3280RL Upgraded a bunch.
|
|
|
03-10-2024, 02:28 PM
|
#12
|
Montana Fan
Join Date: Dec 2022
Location: Union City
Posts: 104
M.O.C. #32153
|
Just a thought, but I have flushed my tank using the port for the high-pressure valve. I remove it and the anode rod and flush from the top of the tank. I get a good flush of the tank from the top-down. I do use a high-pressure nozzle when flushing the tank and have not had a problem.
Best of luck!
|
|
|
03-11-2024, 07:11 AM
|
#13
|
Montana Fan
Join Date: Dec 2017
Location: Holts Summit
Posts: 125
M.O.C. #20913
|
You can remove the heating element to give you another, and larger access. You will need a special socket to remove it.
|
|
|
03-11-2024, 08:00 AM
|
#14
|
Seasoned Camper
Join Date: Dec 2019
Location: Dryden
Posts: 94
M.O.C. #25471
|
I bought one of the plastic flush wands, but never used it after I read about the end blowing off on someone else. I got this one and it's made so the metal wand can't come off. Highly recommend and it's under $10.
https://www.amazon.com/gp/product/B0...e?ie=UTF8&th=1
|
|
|
03-11-2024, 01:53 PM
|
#15
|
Montana Master
Join Date: Oct 2019
Location: Jacksonville
Posts: 2,183
M.O.C. #25165
|
Thanks for the link. I was looking for a replacement that didn't just push onto a barb. That's all I need is to get another one stuck in there.
__________________
Robert & Diana McNeal
2019 Montana Legacy 3791RD 20th Anniversary Edition
2014 F350 4x4 6.7L SRW
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|