|
|
09-08-2022, 10:42 AM
|
#21
|
Site Team
Join Date: Apr 2017
Location: Colorado Rockies
Posts: 1,993
M.O.C. #19755
|
Yes, I think slideouts with rollers are an entirely different animal. The problem we have is the friction caused by not having rollers.
__________________
Scott & Alta
2017 Montana 3160RL, Legacy, Onan 5.5Kw, Solar
2022 F-450 Lariat Ultimate
|
|
|
09-08-2022, 10:50 AM
|
#22
|
Seasoned Camper
Join Date: Aug 2020
Location: Edinburg
Posts: 89
M.O.C. #26856
|
Quote:
Originally Posted by scottz
I don't know what unit you have. Those of us that are doing this modification do not have rollers. The bottom of my slideout is covered with darco (that slick, black, plastic looking material) and sits directly on a wear bar. When the slideout moves, the darco is in direct contact with the wear bar and eventually starts wearing out (usually on the outer edges); not a real great design
|
My slide has rollers. The bottom is covered in the darco. I guess the wood started to get a little rotten, or maybe it's just the heavier mattress we added. But the roller is getting bogged down in a soft spot and tearing up the darco and the wood. I think we caught it pretty early. So I think the metal will work ok here. I am thinking I should probably go ahead and do both sides. I have to figure out how to jack up the slide that is 6' off the ground. Other than that, it looks pretty straight forward.
I have seen slides that have a hard plastic bottom as opposed to the darco. I think my daughter's fr wildcat has that. Is the darco thing just a cost issue? Cheaper for the manufacturer?
|
|
|
09-08-2022, 10:56 AM
|
#23
|
Site Team
Join Date: Apr 2017
Location: Colorado Rockies
Posts: 1,993
M.O.C. #19755
|
Quote:
Originally Posted by dallasrules
My slide has rollers. The bottom is covered in the darco. I guess the wood started to get a little rotten, or maybe it's just the heavier mattress we added. But the roller is getting bogged down in a soft spot and tearing up the darco and the wood. I think we caught it pretty early. So I think the metal will work ok here. I am thinking I should probably go ahead and do both sides. I have to figure out how to jack up the slide that is 6' off the ground. Other than that, it looks pretty straight forward.
I have seen slides that have a hard plastic bottom as opposed to the darco. I think my daughter's fr wildcat has that. Is the darco thing just a cost issue? Cheaper for the manufacturer?
|
Can't say for sure, but in the end, everything boils down to money. I just stacked up wood until a bottle jack would reach the slide beam. You only have to move it a little bit; less than 1/4". Move it too much and you will damage things where the beam goes through the frame.
__________________
Scott & Alta
2017 Montana 3160RL, Legacy, Onan 5.5Kw, Solar
2022 F-450 Lariat Ultimate
|
|
|
09-08-2022, 05:16 PM
|
#24
|
Montana Fan
Join Date: Jan 2020
Location: Hilliards
Posts: 238
M.O.C. #25636
|
I installed them on our 330. If you are mechanically inclined, they are not hard to do. The first one was a bit intimidating because of the unknown, but the second one was a breeze.
When raising the slide, it only needs to go up just far enough to slide the ski in, I would say about 1/8". Any further it would be easy enough to cause some damage to things you don't want damaged!
I seald mine with silicone sealer along the screw rail. They have been in place 2 years now with no problems at all. Good luck!
__________________
2020 MHC 330RL
2021 F350 DRW 6.7 Powerstroke
Retired and Rollin'!
|
|
|
09-11-2022, 07:28 PM
|
#25
|
Montana Fan
Join Date: Jan 2018
Location: Boone
Posts: 311
M.O.C. #21011
|
Quote:
Originally Posted by dallasrules
My slide has rollers. The bottom is covered in the darco. I guess the wood started to get a little rotten, or maybe it's just the heavier mattress we added. But the roller is getting bogged down in a soft spot and tearing up the darco and the wood. I think we caught it pretty early. So I think the metal will work ok here. I am thinking I should probably go ahead and do both sides. I have to figure out how to jack up the slide that is 6' off the ground. Other than that, it looks pretty straight forward.
I have seen slides that have a hard plastic bottom as opposed to the darco. I think my daughter's fr wildcat has that. Is the darco thing just a cost issue? Cheaper for the manufacturer?
|
I just finished our large slide with rollers. Mine sounds just like yours. I used two stainless steel plates, countersunk the screws and re caulked the sides. Only hard part was raising the slide enough. The rollers have a piece of rubber inside the mount that is always pushing upwards. Once I raised the slide enough, I still had to remove the roller to get the plates under them. Good luck, but metal plates are the way to go. Thin and strong.
__________________
2018 Montana HC 362RD
2016 Chevrolet 3500 Duramax HD SRW
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|