|
06-27-2019, 12:37 PM
|
#1
|
Montana Fan
Join Date: Jun 2015
Location: Granite Bay
Posts: 123
M.O.C. #17499
|
Wet bolt problem
This RV lifestyle is soooo much fun. Now on my 17 3790 I have one wet bolt that won’t take grease. I have tried it with the tire on the ground & off. I have taken the zerk off & made sure grease will go through it. I even stuck a wire into the hole, but the wire only goes in a little way.
Any suggestions?
|
|
|
06-27-2019, 01:22 PM
|
#2
|
Montana Master
Join Date: Mar 2019
Location: Milwaukie, OR
Posts: 1,571
M.O.C. #23668
|
when you take the zerk off is there grease inside? I saw on another post of someone with the same issue was that the little hole in the wet bolt was facing down. He removed it and turn it upward, then it took the grease.
__________________
Jeff & Sandi (and Teddy - 7lb Schnorkie)
2018 Montana HC 305RL / HW Progressive EMS
2015 RAM 3500 Laramie Longhorn Crew Cab 4x4 DRW / Demco Recon Hitch on RAM Puck Ball
|
|
|
06-27-2019, 01:30 PM
|
#3
|
Montana Fan
Join Date: Jun 2015
Location: Granite Bay
Posts: 123
M.O.C. #17499
|
A small amount
|
|
|
06-27-2019, 06:50 PM
|
#4
|
Seasoned Camper
Join Date: May 2018
Location: Gering
Posts: 77
M.O.C. #21735
|
Most wet bolts have gnarled(?) heads, not easy to take them apart once they are seated.
. . . If bolt does not take grease, jack axle off the ground to have hole in bolt line up in a different angle... should take when pin hole for grease is off pressure point... If that fails, jack up pivot point between springs to take RV weight off pin hole... may not have to take wheels off ground to free area from blocking pin hole... hope that helps
__________________
7.3L, 10spd F250 towing 2024-Montana High-Country 295RL
|
|
|
06-27-2019, 08:58 PM
|
#5
|
Montana Master
Join Date: Sep 2017
Location: Tacoma
Posts: 1,567
M.O.C. #20475
|
I had one that I had to pull the bolt out and clean out the hole in the bolt it was plugged up and no grease could to through to the bushing. I used a small drill bit and it works great now.
__________________
Bob & Carol Washington St
2017 HC HM352RL 2018 Dodge 3500 laramie CC LB 4x4
Curt Q25 with puck system, Factory air bags
Happy Trails
|
|
|
06-28-2019, 05:34 AM
|
#6
|
Montana Fan
Join Date: Jun 2015
Location: Granite Bay
Posts: 123
M.O.C. #17499
|
I tried to take the nut off of the bolt yesterday, but could not turn it. Don’t have an impact gun, so will wait until I get with some friends. Hopefully one of them will have the right tool.
|
|
|
06-28-2019, 10:49 AM
|
#7
|
Montana Master
Join Date: Jun 2017
Location: POINTBLANK
Posts: 1,916
M.O.C. #19944
|
get a big pipe on the wrench and a buddy to assist
__________________
RAM 22' DRW 3500 Crew LB 40 gal reserve tank / RETRAX Bed Cover / 2020 373RD HC / IS / MOPEKA Tank Monitor / Furrion Side&Rear Cameras
Slide Toppers / EMS-HW50C / Sailun 85's
3rd AC / Dometic 320
|
|
|
06-28-2019, 07:29 PM
|
#8
|
Seasoned Camper
Join Date: Jan 2018
Location: Myrtle Beach
Posts: 81
M.O.C. #21038
|
Impact gun only for removal/loosening... don't use on installation!!
perhaps a pneumatic grease gun might have more pressure to push the clog thru and free it...
|
|
|
06-29-2019, 09:04 AM
|
#9
|
Montana Master
Join Date: Jun 2018
Location: Folsom, California
Posts: 575
M.O.C. #21903
|
I had a wet bolt that wouldn't take grease on right rear spring. By the time I got to look into it (was on 9,000 mile circle of America), here's what I found.
The wet bolt and the bronze bearing had fused together. The side of the brass bearing opposite from the hole in wet bolt had worn very thin. Because the two had fused, eventually the bolt with the knurled portion started to rotate, and wore the hole in the shackle. When I tried to install new wet bolt, hole was worn larger than the knurling, so the bolt wouldn't lock in.
Had to cut shackle from frame and weld in a new one.
I now make sure all bolts accept grease on a regular basis.
__________________
'05 F250 6.0 Bullet Proofed - Sold
'17 F350 6.7 Lariet
'02 Montana 3280RL Upgraded a bunch.
|
|
|
06-29-2019, 10:57 AM
|
#10
|
Montana Master
Join Date: Jun 2004
Location: Benson
Posts: 3,121
M.O.C. #1658
|
Quote:
Originally Posted by milsutter
I tried to take the nut off of the bolt yesterday, but could not turn it. Don’t have an impact gun, so will wait until I get with some friends. Hopefully one of them will have the right tool.
|
Once the nut is off do not try to turn the bolt, it has serrations under the head to keep it from turning and enlarging the hole. You need to drive the bolt out a little then it should turn.
|
|
|
07-03-2019, 07:15 PM
|
#11
|
Montana Fan
Join Date: May 2013
Location: Bartlett
Posts: 197
M.O.C. #13418
|
Today I had one of the rear frame hanger wet bolts that would not take grease. The other rear one was this way a couple of years ago. This time as with the last time both bronze bushings were shot, very thin and only a piece of it this time. Installed a new wet bolt assembly and good to go. I always carry an extra wet bolt. Ordered a replacement also.
__________________
Larry and Jackie Moore
2017 3950BR, MorRyde IS ,Disc.
2022 F350 SRW
|
|
|
07-06-2019, 09:44 AM
|
#12
|
Montana Master
Join Date: May 2007
Location: Montgomery
Posts: 506
M.O.C. #7196
|
Hmm..
Maybe half of my wet bolts take grease anytime I try to grease them.
When I had the wet bolts installed by dealer after 3 or 4 years of RV travel use based on the old advice the OEM plastic bushings would be destroyed in short order, I had the OEM Bolts and bushings returned to me and they were in GREAT shape. So I have to wonder generally speaking how much new grease is needed in every wetbolt all the time...
|
|
|
07-06-2019, 11:40 AM
|
#13
|
Montana Master
Join Date: Apr 2017
Location: 1000 oaks
Posts: 978
M.O.C. #19630
|
Quote:
Originally Posted by Hblick48
I had a wet bolt that wouldn't take grease on right rear spring. By the time I got to look into it (was on 9,000 mile circle of America), here's what I found.
The wet bolt and the bronze bearing had fused together. The side of the brass bearing opposite from the hole in wet bolt had worn very thin. Because the two had fused, eventually the bolt with the knurled portion started to rotate, and wore the hole in the shackle. When I tried to install new wet bolt, hole was worn larger than the knurling, so the bolt wouldn't lock in.
Had to cut shackle from frame and weld in a new one.
I now make sure all bolts accept grease on a regular basis.
|
Wouldn't it have been easier to weld up the hole and redial to size?
__________________
2011 2955RL Gen-Y Executive Kingpin
2022 GMC 2500HD Duramax/Alison
4X4 Crew Cab/Standard bed.
|
|
|
07-06-2019, 02:33 PM
|
#14
|
Montana Fan
Join Date: Jun 2015
Location: Granite Bay
Posts: 123
M.O.C. #17499
|
Ended up taking the wet bolt completely out today. There was no grease on it, and the tiny hole in the bolt was plugged with dirt. Drill out the dirt , put a little bit of grease on the bolt and reinstalled it. Made sure the hole was at 9 o’clock. It took grease after installation, so all is well now! Until the next one won’t take grease!!
|
|
|
07-09-2019, 07:45 AM
|
#15
|
Montana Master
Join Date: Jun 2017
Location: POINTBLANK
Posts: 1,916
M.O.C. #19944
|
Quote:
Originally Posted by milsutter
Ended up taking the wet bolt completely out today. There was no grease on it, and the tiny hole in the bolt was plugged with dirt. Drill out the dirt , put a little bit of grease on the bolt and reinstalled it. Made sure the hole was at 9 o’clock. It took grease after installation, so all is well now! Until the next one won’t take grease!!
|
Don't you just wonder how those things get plugged ??
__________________
RAM 22' DRW 3500 Crew LB 40 gal reserve tank / RETRAX Bed Cover / 2020 373RD HC / IS / MOPEKA Tank Monitor / Furrion Side&Rear Cameras
Slide Toppers / EMS-HW50C / Sailun 85's
3rd AC / Dometic 320
|
|
|
07-10-2019, 06:55 PM
|
#16
|
Montana Fan
Join Date: Jun 2015
Location: Granite Bay
Posts: 123
M.O.C. #17499
|
Yes, it is amazing how it gets plugged
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|