|
03-26-2010, 01:40 PM
|
#1
|
Montana Master
Join Date: Jan 2006
Location: San Antonio
Posts: 1,308
M.O.C. #5165
|
Awining Adjustments
After installing a awning lock according to the instructions and successfully having it lock into the drilled hole, I am having awning problems. I don't think they are related to the awning lock. Here is the problem, facing the awning, the right leg of the awning will not fold up correctly to allow the inner stablizer arm to fit into the outer awning support leg. The left awning stablizer and support nest together as designed. This started to happen after we had the awning extended for several days at the Rally. Several people offerred solutions like centering the awning on the roller--it worked better when it was not centered. I was able to get the awning stored but don't feel like I corrected the problem. Are there any instructions for adjusting the awning for correct storage.
__________________
F-250 King Ranch Crew Cab 2012, Single Wheel, 6.7 L Diesel, Transfer Flow Internal 50 Gallon Fuel Tank, Upgraded Ford Software for 50 Gallon tank, 2006 3475Rl with Mor-ryde King Pin, 2nd AC, 2nd Battery, Pressure Pro TPMS, Wet Bolt Shackle Kit
|
|
|
03-26-2010, 02:18 PM
|
#2
|
Montana Master
Join Date: May 2003
Location: New Bern
Posts: 4,295
M.O.C. #311
|
Quote:
quote:Originally posted by timandsusan
After installing a awning lock according to the instructions and successfully having it lock into the drilled hole, I am having awning problems. I don't think they are related to the awning lock. Here is the problem, facing the awning, the right leg of the awning will not fold up correctly to allow the inner stablizer arm to fit into the outer awning support leg. The left awning stablizer and support nest together as designed. This started to happen after we had the awning extended for several days at the Rally. Several people offerred solutions like centering the awning on the roller--it worked better when it was not centered. I was able to get the awning stored but don't feel like I corrected the problem. Are there any instructions for adjusting the awning for correct storage.
|
Since it works better when not center try making it even more off center. I have to pull my awing all the way to the end on the edge closest to the front to get the rods to line up.
Hope this helps.
|
|
|
03-26-2010, 02:39 PM
|
#3
|
Montana Master
Join Date: Nov 2002
Location: Midlothian
Posts: 956
M.O.C. #40
|
Measure the roller tube to the edge of the awning and make sure the awning is centered on the roller.
You can hold the awning and slide the roller back and forth to center it.
Hope this helps
|
|
|
03-26-2010, 03:26 PM
|
#4
|
Montana Master
Join Date: Sep 2006
Location: Casa Grande
Posts: 5,369
M.O.C. #6333
|
Tim, My awning does this all the time, I just break out the ladder and push them together. I had it adjusted there at Medina Lake, in the RV shop and it worked for a day then went back. I can't seem to move the fabric in the roller. When it goes Tango Uniform I will buy the electric arms and new fabric.....I seem to think that using the deflappers all the time stretches the fabric and will not allow the arms to align properly. That's my story and I'm sticking to it.
|
|
|
03-28-2010, 11:33 PM
|
#5
|
Montana Fan
Join Date: Feb 2005
Location: Virginia Beach, VA
Posts: 328
M.O.C. #3149
|
2005 3400 rl. Same problem. Anchor at top of awning on trlr at front end loose and slides fwd. closed awning. got out ladder. loosened screws on anchor. aligned them with end of awning. retightened and added two additional anchor screws. This helped for about a year of heavy use. Am going to have to adjust again this year as probablem reapperaing. Screwing into the sidewalls does not allow you to tighten the anchor enough. I am add glue this time.
|
|
|
03-29-2010, 03:36 AM
|
#6
|
Montana Master
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
|
You have got to take the tension off the awning to center the awning on the roller. Just lift it up a bit and yank on it. Mine gets pushed off center all the time. Anyone have a idea on how to prevent that.
|
|
|
03-29-2010, 05:19 AM
|
#7
|
Montana Master
Join Date: Sep 2006
Location: Casa Grande
Posts: 5,369
M.O.C. #6333
|
Quote:
quote:Originally posted by richfaa
You have got to take the tension off the awning to center the awning on the roller. Just lift it up a bit and yank on it. Mine gets pushed off center all the time. Anyone have a idea on how to prevent that.
|
Rich, I read in the past when this subject came up that some will put a small screw in the track at the ends of the fabric to keep the fabric from moving.
|
|
|
03-29-2010, 07:03 AM
|
#8
|
Montana Master
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
|
I remember that Phil but I was concerned that it would rip the fabric. The wind will move the awning on the roller. I have mine marked as to where it should be and have Helen yank on it when needed.
|
|
|
03-31-2010, 06:10 PM
|
#9
|
Montana Master
Join Date: Jun 2007
Location: St.Maries
Posts: 1,010
M.O.C. #7329
|
Thanks for the information as we are also having an alignment problem. I will try sliding the fabric and see if it helps.
Topics like this always seem to arise in a timely manner. That is a great thing about this site.
|
|
|
04-01-2010, 04:40 AM
|
#10
|
Montana Master
Join Date: Jan 2006
Location: San Antonio
Posts: 1,308
M.O.C. #5165
|
I can slide my awning in the roller so I will give it another shot! I can tell the alignment gets better when I move it. But like Phil--nothing stays very long--Oh Well--I don't use it that much.
__________________
F-250 King Ranch Crew Cab 2012, Single Wheel, 6.7 L Diesel, Transfer Flow Internal 50 Gallon Fuel Tank, Upgraded Ford Software for 50 Gallon tank, 2006 3475Rl with Mor-ryde King Pin, 2nd AC, 2nd Battery, Pressure Pro TPMS, Wet Bolt Shackle Kit
|
|
|
04-01-2010, 05:57 AM
|
#11
|
Montana Master
Join Date: Apr 2009
Location: Murrieta
Posts: 5,816
M.O.C. #9257
|
LOL clutch... me thinks you almost have it ....
When someone mentions something timely, it does seems to match a problem I am currently having. But even worse, when someone mentions a problem, I soon have THAT problem - well not all the time, but lots of the time (I'm still waiting for my suspension to fall apart). DW and relatives think I'm a genius because a problem occurs and I always seem to know what to do. NOT! I had just read about it on the forum! Someone in another topic mentioned this phenomenon, too!!! I call it psycho-sematic-MOC-itis. Hopefully y'all can come up with something that is easier to say.
As for this topic, the past few trips I am seeing this problem with my manual awning. The left side does not want to nestle into its home rail position just right. A good smack will do it, but I'm finding my step stool is too short and I am gonna have to breakdown and get a taller ladder cuz the smacking is more severe each time and I'm also knocking myself off the stepstool.
|
|
|
04-01-2010, 08:47 AM
|
#12
|
Montana Master
Join Date: Nov 2002
Location: Weatherford
Posts: 1,383
M.O.C. #9
|
Our previous TT had one screw at one end only - never had the fabric rip. I put one in the Montana awning - no problem with the fabric, but that screw didn't help at all when I rubbed up against that tree!!
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
90 day adjustments
|
JnSWells |
General Discussions about our Montanas |
8 |
04-18-2012 08:59 PM |
slide out adjustments
|
ljensen |
Additions & Improvements |
4 |
11-10-2009 12:13 PM |
slide adjustments
|
garyka |
Montana Problems, Problem Solving & Technical Help |
9 |
11-18-2007 09:54 AM |
Slide Adjustments
|
Okie Guy |
Montana Problems, Problem Solving & Technical Help |
0 |
12-25-2006 02:19 PM |
Brake adjustments??
|
Montana Sky |
Tow Vehicles & Towing |
24 |
08-04-2006 03:57 PM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|