|
|
03-22-2020, 11:30 AM
|
#1
|
Established Member
Join Date: Nov 2017
Location: Cornwall
Posts: 44
M.O.C. #20850
|
Crown Moulding
We have a 2018 Montana High Country 305RL The crown moulding and the piece that is attached on the slide out over the kitchen has fallen off on several occasions repaired once by the dealership and then by a carpenter Has anyone had a similar problem and how did you solve the problem I could drive screws into the moulding and the pressboard behind but would not look the greatest
|
|
|
03-22-2020, 12:28 PM
|
#2
|
Site Team
Join Date: Sep 2017
Location: Oro Valley
Posts: 4,086
M.O.C. #20477
|
I used dark screws - you don't notice them.
__________________
Zack and Donna plus Millie and Ranger
2018 3160RL
"Life is too short to stay indoors, enjoy the ride!"
|
|
|
03-22-2020, 12:36 PM
|
#3
|
Montana Master
Join Date: Sep 2013
Location: Pensacola (mail forward service)
Posts: 3,198
M.O.C. #13740
|
Pretty common report. I applied silicone caulk behind the crown molding and pushed the nails that worked out back in place.
__________________
2012 F350 6.7 L dually, 2013 3800RE with 6 pt leveling, Sumitomo 17.5" load range h tires, Samsung 18 cu ft residential fridge, 8k Morryde I.S. with disc brakes. Full timing since 2012.
|
|
|
03-22-2020, 01:07 PM
|
#4
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,774
M.O.C. #12947
|
For the moldings, I've just used 1/4" wide staples that are about as long as what was originally used, and for the fascia around the slides, I just use 1 1/2" brads in my nail gun. I use a combination stapler/nail gun that I carry on the rig along with all my other tools. We've had a number of things come loose over the years, and I just reattach things as they come loose.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
03-23-2020, 09:31 PM
|
#5
|
Montana Master
Join Date: Jan 2016
Location: STAYTON
Posts: 1,118
M.O.C. #18157
|
Silicone adhesive, brad nails hold until the silicone dries.
Mark
__________________
“Hard times create strong men, strong men create good times, good times create weak men, and weak men create hard times.”
|
|
|
03-23-2020, 11:22 PM
|
#6
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,774
M.O.C. #12947
|
Not that this is likely, but you might want to seriously think twice about using adhesive of any kind on the fascia trim around the slides. If these are more permanently attached and there is a need to remove a slide, there can be some serious damage done to these pieces in order to pull a slide. I realize that these parts falling off is not a good thing, but when putting them back on, maybe adding more nails would be a better option.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
03-24-2020, 05:26 AM
|
#7
|
Montana Fan
Join Date: Mar 2018
Location: Atlanta
Posts: 378
M.O.C. #21337
|
I used silicon as well. multiple spots are holding the wood trim pretty well
__________________
Montana 3123RL Legacy 'Boon-docking Edition'
RAM 3500 Mega Cab Cummins Diesel DRW
|
|
|
03-24-2020, 07:38 AM
|
#8
|
Montana Master
Join Date: May 2019
Location: Alton
Posts: 2,898
M.O.C. #24086
|
Use screws to reattach the wood trim. Try to find a stud to anchor into (use a stud finder or better still a Walabot).
Search YouTube for. wood screw caps.
https://m.youtube.com/results?search...ood+screw+caps
This will hide the screw heads. You will need to stain and finish the heads when you are done.
__________________
Daryl and Marianne,
2019 3130re 20th Anniversary Edition
2016 F350 Lariat
|
|
|
03-24-2020, 09:53 AM
|
#9
|
Montana Master
Join Date: Feb 2020
Location: Bencia
Posts: 539
M.O.C. #25828
|
Quote:
Originally Posted by Vic B
We have a 2018 Montana High Country 305RL. The crown moulding and the piece that is attached on the slide out over the kitchen has fallen off on several occasions...........Has anyone had a similar problem........
|
We had a similar problem on our 2014 Montana High Country 305RL. Hired a carpenter to reattach the molding with long screws (recessed and filled to match the molding color and adhesive on the backside I also used a brad gun with longer brads that the original installation to reattach the trim molding around the slides that readily popped off when we brought the slides in/out.
|
|
|
03-29-2020, 02:36 PM
|
#10
|
Montana Fan
Join Date: Sep 2017
Location: ALAMEDA
Posts: 227
M.O.C. #20448
|
Had exactly the same problem. Dealer repair 1st time. Second time the other side came loose and fell onto the floor. I used long screws and countersunk them. I did all 3 slides including the bedroom. No glue used. I used dark screws and they are not noticeable. Took me about an hour and they are now as solid as Gibraltar.
__________________
2017 Montana High Country 310RE
2017 Ram 2500 Diesel, 4 wd crew cab, slr, pulrite super glide, short bed, 2 ea 100 Ah LiFePO4 12 volt Deep Cycle Battery
|
|
|
03-29-2020, 02:58 PM
|
#11
|
Seasoned Camper
Join Date: Sep 2018
Location: Groveport
Posts: 93
M.O.C. #22689
|
We used trim screws to reattach/firm up ours. They are black and have a very small head that is barely noticeable. They use a square bit (several have a bit in the box of screws). We had a couple places where the staples they use to attach them at the factory weren't driven into anything behind the fascia, they we just sticking out into the air on the backside! We were on a 3 month trip when the first one fell and we didn't have the time or tools to glue and clamp or anything.
2019 Montana HC321MK
|
|
|
03-29-2020, 09:48 PM
|
#12
|
Established Member
Join Date: Oct 2017
Location: Sanger
Posts: 46
M.O.C. #20773
|
I had same problem, toke nail gun and put a lot of nails in it, patched the holes. So far so good
|
|
|
03-30-2020, 07:18 AM
|
#13
|
Montana Master
Join Date: Aug 2012
Location: Northport
Posts: 624
M.O.C. #12724
|
Problem is the brad nails have nothing to bite into. You only have a thin piece of paneling and then styrofoam.
__________________
Paul Northport,AL W4XH
2013 358 RLT Mountaineer
2008 Silverado Duramax
|
|
|
03-30-2020, 08:59 AM
|
#14
|
Montana Master
Join Date: Nov 2018
Location: Menifee
Posts: 1,109
M.O.C. #22986
|
I had the same issue with crown moulding. I got these screws ill put a link in this post. CW tried to fix it but it just came off again. Once I fixed it I haven't had a problem since. My Local CW saw the repair and asked how its working, since then the local CW uses these to fix the moulding. Also picked up some colored putty and did a color match, looks great and hasn't budged 10,000 miles later.
tony
https://www.lowes.com/pd/GRK-8-x-1-1...Count/50303191
__________________
2018 3920fb 2020 GMC Denali 3500 4x4 Duramax, 10 speed Allison. LB SRW, Firestone air bags with Airlift wireless onboard compressor. Anderson Ultimate Hitch. MX4 folding cover. 50gal titan in bed transfer tank. Onan 6500 lp genset installed by me ! Had: 2 HF 3500 Inverters with Parallel Kit
|
|
|
03-30-2020, 03:40 PM
|
#15
|
Montana Master
Join Date: Apr 2016
Location: Auburn
Posts: 879
M.O.C. #18474
|
Quote:
Originally Posted by Last2Die
I had the same issue with crown moulding. I got these screws ill put a link in this post. CW tried to fix it but it just came off again. Once I fixed it I haven't had a problem since. My Local CW saw the repair and asked how its working, since then the local CW uses these to fix the moulding. Also picked up some colored putty and did a color match, looks great and hasn't budged 10,000 miles later.
tony
https://www.lowes.com/pd/GRK-8-x-1-1...Count/50303191
|
Did the same exact thing. I used a course threaded wood screw on the first one, then my work partner found those screws you have. She had used them on a desk, then on her Montana, so I did the same.
__________________
2020 Montana 3790RD Legacy EditionOnan, TST TPMS, TrailAir pin, Discs,
2013 F350 DRW 4x4 CC LBViair 10007, Ride-Rites, Westin HDx, 12k Smittybilt
|
|
|
05-24-2021, 07:07 AM
|
#16
|
New Member
Join Date: Nov 2019
Location: Albemarle
Posts: 3
M.O.C. #25256
|
Quote:
Originally Posted by Last2Die
I had the same issue with crown moulding. I got these screws ill put a link in this post. CW tried to fix it but it just came off again. Once I fixed it I haven't had a problem since. My Local CW saw the repair and asked how its working, since then the local CW uses these to fix the moulding. Also picked up some colored putty and did a color match, looks great and hasn't budged 10,000 miles later.
tony
https://www.lowes.com/pd/GRK-8-x-1-1...Count/50303191
|
Thx Tony, we have the same issue going on and was looking for a fix when we get this rig back home. Did you just screw Into the paneling or were you able to find studs to screw to?
|
|
|
05-24-2021, 07:32 AM
|
#17
|
Montana Master
Join Date: Jan 2018
Location: Granger TX
Posts: 2,598
M.O.C. #21044
|
I suppose you could try to find some studs (they are aluminum and not evenly spaced and vary by model) but if you put them into the paneling at opposing angles you should be good to go.
__________________
MikenDebbie Aggie ‘77 in the sticks near Austin TX
2019 Chevy 3500 High Country DRW
2018 Montana 3921FB
Aussie Gus + Texas Heeler Jimmy
|
|
|
05-24-2021, 09:21 AM
|
#18
|
New Member
Join Date: Nov 2019
Location: Albemarle
Posts: 3
M.O.C. #25256
|
Thx we will give it a try has to be better than what was originally done. After 4200 miles we have already had two pieces fall of, decided to wait til we get back to NC to deal with it. Take care!
|
|
|
05-24-2021, 07:33 AM
|
#19
|
Montana Master
Join Date: Nov 2018
Location: Menifee
Posts: 1,109
M.O.C. #22986
|
Quote:
Originally Posted by Partiming2
Thx Tony, we have the same issue going on and was looking for a fix when we get this rig back home. Did you just screw Into the paneling or were you able to find studs to screw to?
|
I screwed right into the paneling. Carefully, the screws will start to grab and you will feel it as they go in. go until they are good and tight and stop, dont over tighten. fill with colored putty and never worry about them again.... 2 cross country trips sense no issues.... haven't even thought about it till this thread came back up LOL. Good luck
Tony
__________________
2018 3920fb 2020 GMC Denali 3500 4x4 Duramax, 10 speed Allison. LB SRW, Firestone air bags with Airlift wireless onboard compressor. Anderson Ultimate Hitch. MX4 folding cover. 50gal titan in bed transfer tank. Onan 6500 lp genset installed by me ! Had: 2 HF 3500 Inverters with Parallel Kit
|
|
|
05-24-2021, 09:22 AM
|
#20
|
New Member
Join Date: Nov 2019
Location: Albemarle
Posts: 3
M.O.C. #25256
|
Thank you. Will try this when we get back home. Take care.
|
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Hybrid Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|