[MAWilsonPE]

USB access is on the bottom of the iN-Command screen panel.

Rip, yes, that is correct.

Here is the original factory floor plan HVAC portion:
{
"name": "HVAC",
"id": "ID_EQUIPMENT_HVAC",
"address": "207",
"info": [],
"category": [
{
"name": "HVAC",
"id": "ID_HVAC_CATEGORY_HVAC",
"order": "9",
"io": [
{
"id": "HVAC 1",
"io_address": "1",
"populated": "Yes",
"label": "Front AC",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "No",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "1"
},
{
"id": "HVAC 2",
"io_address": "2",
"populated": "Yes",
"label": "Middle AC (Optional)",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "No",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "2"
},
{
"id": "HVAC 3",
"io_address": "3",
"populated": "Yes",
"label": "Rear AC",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "Gas/Electric",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "3"
},
{
"id": "HVAC 4",
"io_address": "4",
"populated": "No",
"label": "HVAC Zone 4",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "No",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "4"
}

And here are my changes:
{
"name": "HVAC",
"id": "ID_EQUIPMENT_HVAC",
"address": "207",
"info": [],
"category": [
{
"name": "HVAC",
"id": "ID_HVAC_CATEGORY_HVAC",
"order": "9",
"io": [
{
"id": "HVAC 3",
"io_address": "3",
"populated": "Yes",
"label": "Living Room",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "Gas/Electric",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "1"
},
{
"id": "HVAC 1",
"io_address": "1",
"populated": "Yes",
"label": "Bedroom",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "No",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "2"
},
{
"id": "HVAC 2",
"io_address": "2",
"populated": "No",
"label": "Middle AC (Optional)",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "No",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "3"
},
{
"id": "HVAC 4",
"io_address": "4",
"populated": "No",
"label": "HVAC Zone 4",
"showinmenu": "Yes",
"positionfixed": "No",
"aux_heat": "No",
"vent_enable": "Yes",
"vent_flow": "Yes",
"order": "4"
}

If you are using Notepad, it wants to save the file as a .txt file. You need to select Save As, then select File Type as *.*, then name the file myeditedfile.json

I hope this helps! Best, Mike