Forum: Montana Problems, Problem Solving & Technical Help
12-21-2021, 09:55 AM
|
Replies: 10
Views: 1,595
|
Forum: Montana Problems, Problem Solving & Technical Help
11-16-2021, 07:13 AM
|
Replies: 9
Views: 1,448
|
Forum: Montana Problems, Problem Solving & Technical Help
11-15-2021, 07:29 PM
|
Replies: 9
Views: 1,448
Best Place to Order Hydraulic Cylinder
I need to replace a hydraulic cylinder on our 2008 3400RL. Once I crawl under there and measure the defective cylinder, where is the best place to order its replacement?
I see that etrailer has...
|
Forum: General Discussions about our Montanas
11-08-2021, 07:12 AM
|
Replies: 26
Views: 4,702
|
Forum: General Discussions about our Montanas
11-08-2021, 07:09 AM
|
Replies: 43
Views: 3,745
|
Forum: Montana Problems, Problem Solving & Technical Help
09-27-2021, 07:56 PM
|
Replies: 8
Views: 894
|
Forum: Montana Problems, Problem Solving & Technical Help
09-27-2021, 07:54 PM
|
Replies: 16
Views: 1,982
|
Forum: Montana Problems, Problem Solving & Technical Help
09-27-2021, 09:52 AM
|
Replies: 8
Views: 894
Thanks for the link to the thread. I don’t have...
Thanks for the link to the thread. I don’t have hydac valves on my old rig — just the 4 position manifold with screws that you manually screw in or out to select the slideouts. So since I don’t have...
|
Forum: Montana Problems, Problem Solving & Technical Help
09-26-2021, 09:22 PM
|
Replies: 16
Views: 1,982
|
Forum: Montana Problems, Problem Solving & Technical Help
09-26-2021, 09:21 PM
|
Replies: 8
Views: 894
So i’m thinking that i just need to put 12v to...
So i’m thinking that i just need to put 12v to the center leg of the toggle, then connect the other two terminals (negative) to the two spade connections on the motor for retract/extend.
center...
|
Forum: Montana Problems, Problem Solving & Technical Help
09-26-2021, 06:09 PM
|
Replies: 8
Views: 894
Making a remote for slideout repair
On our last two month trip from AZ to NM, TX, KS, IA, WI, MN, SD, WY, UT and back to AZ, our hydraulic slideouts developed the dreaded “creep” issue which is most likely a leaky cylinder piston. I...
|
Forum: Montana Problems, Problem Solving & Technical Help
09-14-2021, 12:07 PM
|
Replies: 2
Views: 646
|
Forum: Montana Problems, Problem Solving & Technical Help
09-14-2021, 12:06 PM
|
Replies: 14
Views: 1,657
|
Forum: General Discussions about our Montanas
09-13-2021, 04:24 PM
|
Replies: 13
Views: 1,396
|
Forum: Trailers, Tow Vehicles & RV related items for Sale
09-02-2021, 03:24 PM
|
Replies: 1
Views: 1,047
|
Forum: Montana Problems, Problem Solving & Technical Help
09-02-2021, 11:29 AM
|
Replies: 2
Views: 656
|
Forum: Montana Problems, Problem Solving & Technical Help
09-02-2021, 09:42 AM
|
Replies: 2
Views: 656
Hydraulic slideout cylinder test
Yesterday, our 2008 Montana developed the dreaded slideout creep. Was traveling from MN to SD and when I pulled over at a rest stop, I saw that the main slide had creeped out about 4” at the bottom. ...
|
Forum: Tow Vehicles & Towing
08-30-2021, 03:59 PM
|
Replies: 19
Views: 3,016
|
Forum: General Discussions about our Montanas
08-30-2021, 03:55 PM
|
Replies: 3
Views: 678
Fiberglass rear cap
Our 2008 Montana has a fiberglass end cap. I’ve noticed that the newer Montanas do not. Does anyone know when they stopped putting the fiberglass cap on the rear?
I think that’s better...
|
Forum: Montana Problems, Problem Solving & Technical Help
08-27-2021, 05:19 PM
|
Replies: 1
Views: 378
I’ll answer my own post in case anyone else has...
I’ll answer my own post in case anyone else has this issue. Turns out it was squeaking where the drum rubbed against the rubber gasket/bellows. I smeared a little silicon grease on the edge of the...
|
Forum: Montana Problems, Problem Solving & Technical Help
08-27-2021, 05:15 PM
|
Replies: 2
Views: 579
|
Forum: Montana Problems, Problem Solving & Technical Help
08-24-2021, 12:52 PM
|
Replies: 3
Views: 662
Like Carl N Susan said, drop the coroplast and...
Like Carl N Susan said, drop the coroplast and access the valves. Mine were also plumbed in to tight to remove the valve after unbolting it. Like him, I ended up cutting out about a 2” section of the...
|
Forum: Montana Problems, Problem Solving & Technical Help
08-24-2021, 12:41 PM
|
Replies: 1
Views: 378
Pinnacle MJ9250D dryer
We recently had to move the stacked Majestic washer/dryer from its shoehorned location in the closet next to the entryway in our 2008 3400RL. The only way I could manage to get the thing out was to...
|
Forum: Maintenance
05-31-2021, 08:12 AM
|
Replies: 12
Views: 2,112
|
Forum: New Member Introductions
05-31-2021, 08:07 AM
|
Replies: 20
Views: 2,723
|