|
09-09-2006, 03:59 PM
|
#1
|
Seasoned Camper
Join Date: Jun 2006
Location: Greenfield
Posts: 65
M.O.C. #5913
|
3400RL Heating Ducts
Hello all!
I purchased a 2006 3400RL this summer and have just recently tried out the heating system. There are four floor ducts; one in the bedroom, one in the kitchen, and two in the rear living room. I get heat out of all ducts except the kitchen. Is there a damper or something similar or is this a problem for my dealer to fix?
Thanks
|
|
|
09-09-2006, 04:59 PM
|
#2
|
Montana Master
Join Date: May 2006
Location: Ronan
Posts: 513
M.O.C. #5756
|
humm thats a good question I 'll give mine a look and get back to you
tim ford
|
|
|
09-09-2006, 05:05 PM
|
#3
|
Montana Master
Join Date: Aug 2004
Location: Fallon
Posts: 6,064
M.O.C. #1989
|
Sounda like you need to contact the dealer. We get plenty of heat out of ours without doing anything although I think the 06 has heater in a different place than the early 05.
Happy trails..........................
Sue and Ed Rowe
Hemet California 2005 3400RL 2006 GMC 3500 Dually, D/A, Crew Cab, Long Bed
|
|
|
09-09-2006, 05:09 PM
|
#4
|
Montana Master
Join Date: May 2006
Location: Ronan
Posts: 513
M.O.C. #5756
|
I just got back in and tried mine out and get heat in all vents and couldn't find a way to close off one from the others so i'd say judging bye mine it is a dealer problem but I must say it's confusing a little because your getting heat out of the living room vents they all follow the same path
tim ford
|
|
|
09-09-2006, 05:58 PM
|
#5
|
Montana Master
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
|
Take off the vent and stick your hand down there and see if you can feel the airflow.We had the same problem . There was plenty of airflow it just roaring right by and not deflecting up.We got a vent from Home depot with the adjustable vanes and they reacxed down far enough to deflect the heat up..check it out...
Rich& Helen N.Ridgeville,Ohio.
F-350SD, Lariat, V-10,4:30 Diff, tow command Long bed, Crew Cab Dually, 06 3400RL
Mor-Ryde Pin Box
|
|
|
09-09-2006, 06:49 PM
|
#6
|
Montana Fan
Join Date: Jan 2006
Location: Sioux Falls (full-time)
Posts: 343
M.O.C. #5293
|
It's normal, that was my question during the PDI. You can get a deflector if you want. It's mainly caused due to where the furnace (blower) is located. The forced air of course blows through the duct and of course the end of the duct is in the living room where it is forced out. You're going to get more air blowing out in that area because it hasto go somewhere because it's at the end of the route and it's being forced out with no place else to go but out. Some heat comes out of the kitchen it's just not forceful because of physics, but like richfaa said get a deflector and it should work fine and cause the air to stop a good portion of it in mid-stream while trying to travel to the living area forcing it out of the kitchen vent. Is that as clear as mud? I'm confusing myself. ha!
2006 Montana 3500RL, MorRyde Suspension, W/D, 2nd A/C, Fantastic Fans, MaxxAir, Fireplace, RotoChocks, Slide Awnings. 2005 Ford F350 Lariat LE, PSD 4x4 Dually, Long Bed, C-Betr Mirrors, Vortex Spray-In Liner, Access Tonneau Cover, Remote Starter/Alarm, LED Running Board Lights
|
|
|
09-09-2006, 08:29 PM
|
#7
|
Montana Master
Join Date: Jan 2004
Location: Down the Road
Posts: 5,627
M.O.C. #889
|
I have not had any trouble w/ my heater vents. Guess I am one of the lucky ones on this issue... LOL!
2004 Chevy Silverado LT 2500HD CrewCab Duramax
2004 Montana 3400RL
|
|
|
09-10-2006, 01:37 AM
|
#8
|
Montana Master
Join Date: Jul 2006
Location: K.C.
Posts: 11,731
M.O.C. #5980
|
All of you said it very well, I'll add my 2 cents worth;
The furnace blower is basically pressurizing a tube, the air comes out stronger at the ends of the tube, so you should buy registers with adjustable dampers, so you can fine tune where the air goes.
When we balance a new heating and cooling system, we adjust some main dampers in the ducting, then go to each register or diffuser and adjust the dampers there to get a balanced system.
All the builders had to do for us, is give us floor registers with dampers in them, so we can do the balancing job, when we take possession of our Montana's. Cheap, cheap...HEAR THAT MONTANA FACTORY?????
There, I feel better.
Ozz
'07 3400RL 2nd RTU
2 Golf Cart batteries 3,000 watt inverter, automatic transfer switch
Honda 2000 Generator, Maytag's with 220 Dryer
Stationary domed Sat. dish, LCD 12 Volt Amp gauge, LCD Tank Monitor
3 added 120 volt outlets, On Board Air; 12 Volt Viair 450C compressor
2006 Ford PSD 4x4 Off Road Lariat, Hadley Air Horns, Truck inverter with 110 volts: laptop, Color Backup camera, Firestone air bags,Husky air ride roller hitch, Awning lock
|
|
|
09-10-2006, 03:42 PM
|
#10
|
Seasoned Camper
Join Date: Jun 2006
Location: Greenfield
Posts: 65
M.O.C. #5913
|
The problem was sucessfully solved!
I added a small piece of aluminum roof flashing into the duct. Just enough to divert some of the passing air up into the room. Works perfect now.
Thank you all for the help!
|
|
|
09-11-2006, 07:09 PM
|
#11
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
I'm going to have to try the roof flashing idea. Thanks ChiefKB.
I did as Rich suggested and felt down in the duct. Lots of air going right on by that vent. I got the adjustable covers from HD and put then on all vents. It only improved it a slight bit. Mostly it helped shut down the heat in the bedroom. That room got downright hot from all the air flow so we're able to control that now. But I need the flashing to divert some of the heat into that vent in the kitchen.
ChiefKB, how much is "just enough" About an inch sticking up into the duct from the floor of the duct? All the way across? Sorry, I could use some help on this one.
See another Montana or Mountaineer on the road? Flash lights twice, it might be one of us!
Steve Reigle (pronounced Regal)
Fulltiming since 3/21/03
'07 3400RL
'05 Ford F250 SD Lariat CC SB 6.0L PSD/TS FX4 4x4
Our RV Travels (now Firefox-compatible)
|
|
|
09-19-2006, 05:49 PM
|
#12
|
Seasoned Camper
Join Date: Jun 2006
Location: Greenfield
Posts: 65
M.O.C. #5913
|
The piece of flashing I used was 1" X 1" X 6". I tucked it between the floor and linoleum. There is enough pressure when you tighten the screws up to keep it in place. Moving is side to side along the long edge seemed to increase/decrease the amount of air diverted upward into the kitchen.
Chief KB
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Heater Ducts
|
JohnG3 |
General Discussions about our Montanas |
14 |
05-27-2014 06:37 PM |
Furnace Ducts?
|
barmar |
Montana Problems, Problem Solving & Technical Help |
1 |
05-08-2011 10:54 PM |
Heat Ducts
|
Campingmike |
Additions & Improvements |
10 |
04-10-2011 05:14 PM |
Furnace Ducts
|
Montana_1306 |
Montana Problems, Problem Solving & Technical Help |
0 |
03-28-2004 12:34 PM |
Exposed heating & air conditioning ducts
|
D and M On The Road |
What I'd like to say if... |
0 |
07-11-2003 08:00 PM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|