|
12-21-2006, 01:26 PM
|
#1
|
Montana Fan
Join Date: Jul 2006
Location: New Richmond
Posts: 153
M.O.C. #6103
|
Front fiberglass cap
Today while cleaning my 2003 3670RL Montana, I noticed the bottom was loose accross the front lower portion. I pulled the plastic strip off from the channel, and it was full of water, and all the screws were rusted off. There was not one good screw left. I will be replacing the screws, but not putting the plastic cover back on. It holds water, and rusted everything out. Now I think I want to remove the lower cover, and inspect for frame rust also, It will also give me an opportunity to look for broken welds too. Check yours, all you have to do is push up on the lower front and if it's loose, you got the same problem...no matter what model
|
|
|
12-21-2006, 01:36 PM
|
#2
|
Montana Master
Join Date: Sep 2004
Location: Leona
Posts: 6,382
M.O.C. #2059
|
Thanks Rog,
Another item to add to my check list for when I return. It will be a month of work before I can get on the road. Be sure to post the results if you do further checking. Merry Christmas.
|
|
|
12-21-2006, 04:41 PM
|
#3
|
Montana Master
Join Date: Aug 2006
Location: Lone Tree
Posts: 5,615
M.O.C. #6109
|
Montana Rog -
Had my front belly off several times last summer to check welds, and I noticed the same problem. All the screws were corroded and rusted. The only real thing holding it together was the silicone. The rubber cover kept the screws from falling out on the road I guess .
You've probably got the right answer by just leaving the rubber cover off. I don't see any other way to keep it drained. BTW, I don't think anything in that belly cover will actually hold much water, as it just drains out the pin box opening or down into the front cabinets which are open to the street. I don't think any of that will contribute to rust on the frame (I had none at all), but it is an excellent idea to get in there and check the welds - every year.
|
|
|
12-22-2006, 04:15 AM
|
#4
|
Montana Master
Join Date: Oct 2006
Location: Choctaw
Posts: 530
M.O.C. #6364
|
What about drilling some small drain holes where the water collects?
|
|
|
12-22-2006, 02:28 PM
|
#5
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
While we're talking water accumulation, drill about 3 small holes in the underside of the bottom rung of the ladder. They tend to accumlate water and eventually rust through. When I drilled our new one within a couple of weeks of its build date water ran out of the first hole I drilled. There was already one small hole there but it was plugged with crud. I like having three holes better.
|
|
|
12-22-2006, 02:33 PM
|
#6
|
Montana Master
Join Date: Sep 2006
Location: Wappingers Falls
Posts: 1,303
M.O.C. #6263
|
Hi Steve, Your talking about the bottom one that folds upside down on top of the second and beomes a catch pan? Sound like another to add to my todo list...will I have any time to use my rig!
Thanks, Chuck
|
|
|
12-25-2006, 03:16 PM
|
#7
|
Montana Master
Join Date: Nov 2004
Location: Oak Harbor
Posts: 1,530
M.O.C. #2471
|
It's a little pricey to do, but I have replaced every external screw with stainless steel screws because of the rust problem with the stock ones. Just remember to place some silicone on the threads of the replacement screws when putting them in.
__________________
Previous:2004 Mountaineer 325FKBS,2010 Montana 3455SA Now:2018 Bighorn 3575EL (SOB's ) Res. Fridge,W/D,Disc Brakes,Water Softener,Dish Tailgater PRO,LioN Batts, several mods.
2021 RAM 3500 Laramie.... "LOADED", 4x4, SB H.O. 6.7L, Aisin Trans, PullRite Super Glide Hitch, 52 Gallon Titan Fuel Tank.
|
|
|
01-01-2007, 02:02 PM
|
#8
|
Montana Fan
Join Date: Jul 2006
Location: New Richmond
Posts: 153
M.O.C. #6103
|
Well, I found out there are only two screws holding the front cap on the bottom. It is the two closest to the hitch..on either side of it. The rest of them are 1/2 inch long, and just attach the cap to the bottom cover. I also did drill some drain holes in the bottom skin at the front and rear of the two ribs under there. It is the low point, and will drain any water that may accumulate there.
|
|
|
01-06-2007, 09:02 AM
|
#9
|
Montana Fan
Join Date: Feb 2006
Location: Cinnaminson
Posts: 197
M.O.C. #5316
|
Hi Montana Rog,
I, too, have a 2003 Montana 3670RL and, because of a front wardrobe shelf dropping, found that several welds on the curb side and two more on the driver side were broken. The dealer contacted the factory and my 3670RL is being welded as we speak. My dealer took pictures of the broken welds and Fed-Xed them to the facoty. The factory gave explicit directions on how to fix it (at their cost). I should get it home this upcoming week. I hope this solves it!
|
|
|
01-06-2007, 04:45 PM
|
#10
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
Art, that sounds like the dreaded frame flex problem Montanas of that era sometimes suffered, including our 2003 3295RK. Keystone was good about fixing it for us.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|