|
07-09-2018, 07:43 PM
|
#1
|
Montana Master
Join Date: Jan 2018
Location: Austin
Posts: 2,418
M.O.C. #21044
|
Skirt popped out of black gasket
Stopped at a Walmart this afternoon and noticed a section of the roadside skirting had popped out of the black rubber gasket. DW figured out to pop it back in. Don’t know if this is common or not. I’m glad I found it before any damage occurred. Even with it popped back in place it felt sorta flimsy. Right or wrong - I caulked along the bottom edge of the gasket with silicone hopefully to give it a little help to stay in place. Does this happen often and what is the correct fix? The pic below was taken after DW had snapped much of it back in place...
__________________
MikenDebbie Aggie ‘77 in the sticks near Austin TX
2019 Chevy 3500 High Country DRW
2018 Montana 3921FB
Aussie Gus + Texas Heeler Jimmy
|
|
|
07-09-2018, 09:02 PM
|
#2
|
Montana Fan
Join Date: Jun 2017
Location: WESTMINSTER
Posts: 159
M.O.C. #20081
|
Happened to me at speed but mine came loose the same place yours did but came out all the way to the fender and flapping in the wind like a flag. Pulled over got it back in and gorilla tape it until we got to campground and next day siliconed it all over and seemed to work for me .Good luck with it just keep checking as i do.
|
|
|
07-09-2018, 09:38 PM
|
#3
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,700
M.O.C. #12947
|
We’ve had this happen a lot. In fact, just noticed today the panel just forward of the door was out. The problem seems like they didn’t assemble the aluminum quite high enough to completely secure the panel with the metal strip and screws. I did the rear panel a while back, removed all the screws and nudged the panel up enough to get screws into it, and since it hasn’t come loose. This section will be my next project, as it’s drifting down below the pass through door trim.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
07-10-2018, 05:05 AM
|
#4
|
Montana Master
Join Date: Jan 2018
Location: Austin
Posts: 2,418
M.O.C. #21044
|
Securing skirt panel
Rohrman - did you add screws along top edge? When I first surveyed the issue my first thought was “why didn’t they attach this with screws along the top and use the gasket to cover the screws?” What structure is behind there if screws are used along the top?
I wanted to put some gorilla tape on it for additional insurance while the silicone cured but DW was worried the tape might pull off some paint so I did not use the tape. It held fine for the final 40 mile leg to the campground.
__________________
MikenDebbie Aggie ‘77 in the sticks near Austin TX
2019 Chevy 3500 High Country DRW
2018 Montana 3921FB
Aussie Gus + Texas Heeler Jimmy
|
|
|
07-10-2018, 05:39 AM
|
#5
|
Montana Master
Join Date: Apr 2016
Location: Auburn
Posts: 879
M.O.C. #18474
|
This was a very common thing starting in late '15 with Montanas. Mine has done it twice and our dealer says they repair 3-4 a month on average. Just like mentioned above, screws will keep them there, not the staples they had in mine originally.
__________________
2020 Montana 3790RD Legacy EditionOnan, TST TPMS, TrailAir pin, Discs,
2013 F350 DRW 4x4 CC LBViair 10007, Ride-Rites, Westin HDx, 12k Smittybilt
|
|
|
07-10-2018, 01:56 PM
|
#6
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,700
M.O.C. #12947
|
Ours have an aluminum strip that is screwed on, and the rubber strip snaps on the aluminum to cover the screws. The problem I have is the panel wasn’t mounted high enough so the screws actually went through it.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
07-14-2018, 05:30 PM
|
#7
|
Montana Fan
Join Date: Jan 2007
Location:
Posts: 126
M.O.C. #6748
|
I have the same problem on my bedroom slide in our 3711fl. The dealer had to replace the original "J " metal panel because the damaged it installing my slide toppers. The panel pops out just like the photo shown. I removed the rubber and aluminum strip and refastened it with clear silicon applied to the top and bottom of the rubber. I looked at it again the other day and it was popped out again! I now know what the problem is- the sun hits that panel all afternoon and heats it up to the point of expansion and buckles the panel. So the dealer cut the "J" metal to long on the sides where it is attached to the slide vertical molding and the metal when hot has to go somewhere. I am going to wait for a cooler day and completely remove the whole apparatus, trim the sides of a 1/4 inch or so and reattach. That should take care of it. No other panel on our rig has this problem except the one touched by the dealer who I fired when the one year warranty was up on our newest rig of the three we purchased from them.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|