|
10-29-2017, 07:23 AM
|
#1
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
Maxx Air Fan issues -
We are working out the bugs on a new 3730FL Montana. One Maxx Air Fan motherboard was sent from factory for replacement as a DIY project. Ok - should be a plug and play - but can someone tell me how to access the motherboard from the base of the fan? Anyone have experience doing this project?
Thanks,
Max
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
10-29-2017, 11:17 AM
|
#2
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,697
M.O.C. #12947
|
Don't have that fan, but it looks like you might have to remove it from the ceiling to access the circuit board. Go to this link and you can find the document that will show you where the board is located. http://www.airxcel.com/maxxair/servi...cument-library
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
10-29-2017, 07:07 PM
|
#3
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
Boom - there it is - Thanks Bob. Now I just have to figure out how to get in there. There are some pigtails on the circuit board which I am assuming are for connection in series, which I dont have. I assume those can just be tucked away in a recess after a bit of electrical tape to the ends. Looks like it willl just plug in then.
Thank you sir.
Max
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
10-29-2017, 07:26 PM
|
#4
|
Montana Fan
Join Date: Dec 2014
Location: Warrior AL, usually
Posts: 184
M.O.C. #15888
|
I had to replace that PC board on mine several weeks ago. You don't have to remove the whole fan assy. It can be replaced from below.
Remove the screen by turning the plastic tabs that hold it in.
Remove the knob (screw in the middle).
There are several screws around the edge that hold the escutcheon in place - remove them. The PC board is now visible.
Remove the (two, if I remember correctly) screws that hold the PC board in place. The board will now be free.
There are 5 or 6 inline connectors and PC board mounted connectors to disconnect. Be careful as you disconnect them, one of them is connected to a small, thin wire that can be damaged. The only trouble I had was pulling the cables out of the space between the fan housing and the ceiling cut out - they were just stuffed in there to take up the slack, and they were tight to get out. The only other thing to be aware of is that one of the sensors and one of the small wires is hot glued into place. You will have to re-glue these.
It's not as bad as it sounds - just go slow and be sure to disconnect/reconnect all the cables to the board. The connectors are all different size/configs, so you can't get a cable in the wrong place. Re-stuffing the cables back into the void to get them out of the way was probably the worst part.
|
|
|
10-29-2017, 08:37 PM
|
#5
|
Montana Master
Join Date: Jun 2010
Location: Colorado Springs
Posts: 3,335
M.O.C. #10496
|
I suggest you take picture before and during disassembly. This works for me so I don't have to remember what goes where when I reassemble things. Good luck with your project.
__________________
2010 3150RL
LevelUp, Dual 6 volt batteries, Progressive Industries EMS HW50C, Honda EU2000i Generator, Bridgestone Duravis R250 tires, Torklift Glowstep Revolution Stairs, LED Tail lights
2015 RAM 3500 Laramie SRW LB CC Cummins 6.7L Aisin Trans B&W RVK3600
|
|
|
10-29-2017, 08:55 PM
|
#6
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
Thank you Bama. I appreciate step-by-step instructions. I mo get on this next chance I have.
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
10-29-2017, 08:56 PM
|
#7
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
CoRattler - very good advice. - will do!
Max
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|