|
|
11-28-2011, 06:38 AM
|
#21
|
Montana Fan
Join Date: Apr 2011
Location: Castle Rock
Posts: 248
M.O.C. #11369
|
I have to use a dead blow hammer to get the pins out of the hitch-hard for someone to do as a joke.Hitch is 14 years old and still tight.I do check everything after a stop.Hitch is a Draw-Tite
|
|
|
11-28-2011, 08:11 AM
|
#22
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
Not positive about Husky pins, but looking at them on the company website they appear to be the same or similar to Reese pins.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
11-28-2011, 12:55 PM
|
#23
|
Montana Fan
Join Date: Feb 2009
Location: Redlands
Posts: 460
M.O.C. #9135
|
Does anybody know if the locking pins work on a Curt hitch?
__________________
2011 3150RL
|
|
|
11-28-2011, 02:27 PM
|
#24
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
If it's a standard pin with the notch on the end for the clip to fit over the reese locking plates will work because they just slide over the notch and then a lock goes a hole in the end.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
11-28-2011, 02:29 PM
|
#25
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
Sorry, dropped the last part here's the rest of it: If the pin has a hole in the end then usually you can drill the hole out and put a small padlock on.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
11-29-2011, 05:29 PM
|
#26
|
Montana Master
Join Date: Dec 2010
Location: Anytown
Posts: 609
M.O.C. #10966
|
I use some of the locking plates with substantial padlocks for my Superglide and Rails, but I also use a few receiver hitch locking pins. Still do a visual though, and yes I also have a pretty beefy padlock on the release handle!
With the my hitch and rail setup, I think I must have about 6-8 locks of one kind or another...such is our society today!
__________________
2011 Montana 3580RL with a Reese 20k GooseBox w/offset B&W ball, Sailuns, RoadMaster shocks, Splendide stacked washer/dryer, some other stuff...
2015 Ram 3500 DRW Laramie Megacab, Aisin w/3.73s, 255/80 17 Toyos A/T III, rear auto level, 40 gal. fuel/tool combo box, some Banks mods...
|
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|