|
07-01-2007, 06:41 AM
|
#1
|
Established Member
Join Date: Nov 2006
Location: Mesa
Posts: 31
M.O.C. #6552
|
slider
Ok all you trouble shooters, help me with this: we're returning from a somewhat trouble free 3 week journey. More on the 'somewhat trouble free' part later. Here's my question on the kitchen side slide out: Two nights ago when we tried to extend the slide out, only one end would slide, leading to torquing or pivoting, while the other end remained "in". Has this happened to anybody else? Any ideas on what's causing this? By the way, this is happening on a 2005 Big Sky.
I was able to get it fully extended by pushing/wiggling on the counter top on the end that was not moving. In the morning, when we tried to retract it, it was again moving only on one end. With someone outside, pushing on the non-moving end of the slide out, and with me on the inside, pulling on the countertop, we were able to fully bring it in.
|
|
|
07-01-2007, 07:53 AM
|
#2
|
Montana Master
Join Date: Nov 2002
Location: Hartselle
Posts: 977
M.O.C. #45
|
Sounds like to me that you have a bolt sheared on your slide. Check under the slide and see if you have a 1/4 20 bolt missing or sheared. Several on here has had that happen to them. Do a slider search on here and you will find some pictures showing the problem.
|
|
|
07-01-2007, 03:12 PM
|
#3
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
As Larry & Roma said, there is a shear bolt on each end of the square shaft that runs parallel to the coach, under the slide. The result of a broken shear bolt is exactly what you described. The bolt you want to buy is available at Home Depot or Lowe's. Per MIMF, formerly a Lippert employee, the bolt you want is 1/4-20 x 2" hex head Grade 8 bolts. Get some washers also. This bolt has a shoulder long enough to go through the entire shaft so that NO threads are inside the shaft. The threads are a weak point and are why many of the original bolts have broken. Because the shoulder will extend beyond the shaft, you'll use washers to fill the gap between the nut and the shaft so the nut will snug up.
The biggest problem I had was getting the slide aligned properly so that when it closes it is snug to the coach on both ends. You can use a crescent wrench or open end wrench on the square tube to turn it. That will move one end of the slide. Align the holes and insert the bolt.
It's easiest if you can get the slide all the way in and snug to the coach before doing this. I couldn't get to the tube to work with it so had to have the slide out a ways and then had to do some adjustment to snug it up.
Good luck. I hope this helps. I've only had to do this once and hopefully never again.
|
|
|
07-02-2007, 02:52 PM
|
#4
|
Established Member
Join Date: Nov 2006
Location: Mesa
Posts: 31
M.O.C. #6552
|
Wow, I knew I could rely on you guys to come up with the answer. I have been reading this forum for months now and I am forever amazed at the knowledge one gets from cyberspace. Thanks again, I will let you know whne I get my monte back on the road. I am sure that is the problem because I am sure it happened coming out of Denver heading south on the 25. What a miserable hwy that is. Ive been on dirt roads in better condition.
|
|
|
02-23-2018, 06:11 PM
|
#5
|
Established Member
Join Date: Jun 2017
Location: Vestal
Posts: 10
M.O.C. #20055
|
Here’s a bedroom slider question that seems related. A week into an extended trip, we arrived at a new site tonight and our bedroom slider seems get stuck at the top after it moves out about a foot. The bottom keeps moving so that the slide starts to tilt at an angle inward. We’ve tried checking for obstructions, pushing, etc, but no luck. Help
Please!
|
|
|
02-23-2018, 07:43 PM
|
#6
|
Montana Master
Join Date: May 2011
Location: Hixson
Posts: 3,436
M.O.C. #11397
|
Wow! Having trouble ALREADY on a unit that is ONLY 13 years old? Unacceptable!
Oops, sorry. Just noticed dates.
__________________
2018.5 Montana 3791RD
Full Timers 9/1/2010 through 1/16/2020.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|