|
02-11-2012, 10:25 AM
|
#1
|
Montana Fan
Join Date: Oct 2008
Location: Cleveland
Posts: 366
M.O.C. #8881
|
Galley Tank valve rod support
I had to replace my galley tank valve because the rod is about 12 inches long and there is no support where it comes out of the belly material. If the handle is pushed down toward the ground it will break the valve where the rod screws into the valve..
This is what I did to support the rod.
We have a 3000RK..
lfw..
|
|
|
02-11-2012, 11:10 AM
|
#2
|
Montana Master
Join Date: Apr 2007
Location: South Shore
Posts: 6,009
M.O.C. #7110
|
Nice mod, looks like it will do the job fine!
__________________
2011 GMC 4X4 dually CC, 6.6 Duramax with Allison Transmission. Formally 2001 Montana,2007 3400RL Montana, presently 2018 3401RS Alpine.
|
|
|
02-11-2012, 11:33 AM
|
#3
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
Nice job! Looks like a good solution.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
02-11-2012, 12:06 PM
|
#4
|
Montana Master
Join Date: Feb 2004
Location: Brandon
Posts: 3,944
M.O.C. #1034
|
Very nice!!!
__________________
Darwin & Maureen DeBackere
Minnedosa, Manitoba, Canada
2011/3500/Silverado/4x4/DRW/Duramax
2017/3721RL/Legacy Pkg./Pressure-Pro
|
|
|
02-11-2012, 12:47 PM
|
#5
|
Montana Master
Join Date: Jan 2006
Location: South
Posts: 2,499
M.O.C. #5140
|
Nice tin bending!
We removed our galley tank handle, rod and cable and instead installed a remote, electrically operated valve. I was ruining shirts by snagging them on the slide rails; the $100 or so I spent has already been recouped!
|
|
|
02-11-2012, 03:38 PM
|
#6
|
Montana Master
Join Date: Jun 2010
Location: Colorado Springs
Posts: 3,335
M.O.C. #10496
|
Good design, low cost and effective! Good work. Thanks for posting the photos.
__________________
2010 3150RL
LevelUp, Dual 6 volt batteries, Progressive Industries EMS HW50C, Honda EU2000i Generator, Bridgestone Duravis R250 tires, Torklift Glowstep Revolution Stairs, LED Tail lights
2015 RAM 3500 Laramie SRW LB CC Cummins 6.7L Aisin Trans B&W RVK3600
|
|
|
02-12-2012, 12:50 AM
|
#7
|
Montana Fan
Join Date: Oct 2008
Location: Cleveland
Posts: 366
M.O.C. #8881
|
snfexpress I am not that good at tin bending.. so I did the next best thing.. a nice piece of aluminum angle.. Drilled a hole just a little bigger than the rod at a slight angle, rounded the corners and used self taping screws.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|