|
|
11-11-2018, 11:49 PM
|
#1
|
Montana Fan
Join Date: Apr 2014
Location: Eureka
Posts: 276
M.O.C. #14208
|
Problem with my B&W Companion Hitch
I have a B&W Companion Hitch. Went to unhook and it would not unhook. The jaws will not open. When I move the lever it does not move the jaws. Acts like something might be unhooked or broken in the hitch. With the lever open I tried to pry the jaws open but they would not move. I did not pry too hard did not want to break something. The hitch is about 7 years old. Any ideas? I have a 2015 Ford Platinum Short Bed and a 2014 Montana 3582RL.
Jim and Margie Bonhote
2014 Montana 3582RL
2015 Ford F350 Platinum
|
|
|
11-12-2018, 04:08 AM
|
#2
|
Montana Master
Join Date: Oct 2017
Location: Bastrop
Posts: 2,892
M.O.C. #20753
|
I have a new B&W I sometimes have the same issue. just putting the truck into reverse or drive is enough to relieve the binding on the jaws to allow it to open.
I find it is worse the worse the 5er is level side to side.
__________________
Mocha, one-eyed toothless, hurricane survivor, Pirate dog
2019 20th Anniversary Edition 3701LK
B&W 20K for Ford OEM Puck
2018 Ford F-350 Lariat CCLB PSD DRW KJ5CQH
|
|
|
11-12-2018, 05:02 AM
|
#3
|
Montana Master
Join Date: Oct 2017
Location: Trinidad, TX
Posts: 506
M.O.C. #20746
|
Had a similar situation last Friday. I just pulled forward several feet and reversed to our target position and it worked fine. First time it has ever happened. I think the king pin was pressed into the jaws and would not allow them to release.
__________________
2018 Ram 3500 Laramie Longhorn 4X4 Dually Cummins Aisin CC LB / B&W Companion hitch
50 Gallon Transfer Flow in bed tank w/ Trax 3
2018 Montana 3121RL
|
|
|
11-12-2018, 05:49 AM
|
#4
|
Montana Master
Join Date: Oct 2004
Location: Salem
Posts: 7,550
M.O.C. #2283
|
If that hitch is in a bind it will NOT open. If it’s not level with the truck, the camper pulling it to one side. Get a hammer crawl up in the bed of your truck and beat on the jaws, might help. Move the truck back and forward, easily pull and push on the camper with the landing gear down, raise the camper up and down. What ever it takes get it out of a bind.
Lynwood
|
|
|
11-12-2018, 06:59 AM
|
#5
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
If moving back and forth a little doesn't do it, call B&W before you beat on it. They are great to work with.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
11-12-2018, 07:11 AM
|
#6
|
Montana Master
Join Date: Jul 2014
Location: Upstate NY
Posts: 1,788
M.O.C. #14547
|
I have had that happen 3-4X. I 'corrected' it by jockeying the combo back and forth. I will admit that the first time was a bit disconcerting but once figured out, not really a problem. My hitch is 9 years old and has about 50K miles otherwise uneventful towing 12K plus 5ers
__________________
Dave W
2014 Montana High Country 343RL (Sold!)
2011 Ford 6.7 Lariat CCLB (Went to PU Heaven)
2019 F150SC XLT SE Sport,w/full tow package
|
|
|
11-12-2018, 07:44 AM
|
#7
|
Montana Master
Join Date: Apr 2016
Location: Auburn
Posts: 879
M.O.C. #18474
|
When the camper is raised by the jacks and still has pressure on the jaws, the handle will not release them. When this happens, I get back in the truck and put it in neutral and release the brake for a second. That is usually enough to take the pressure off. It's only happened a few times in the 35k miles I've pulled them.
__________________
2020 Montana 3790RD Legacy EditionOnan, TST TPMS, TrailAir pin, Discs,
2013 F350 DRW 4x4 CC LBViair 10007, Ride-Rites, Westin HDx, 12k Smittybilt
|
|
|
11-12-2018, 11:47 AM
|
#8
|
Montana Master
Join Date: Mar 2016
Location: Catoosa
Posts: 780
M.O.C. #18384
|
I think that the OP is stating that the handle IS moving, just not opening the jaws. If that is indeed the case than there is probably a pin or something that has come loose. You need to look under the hitch and see if you can find the problem. If necessary, you can remove the pins that attach the hitch to the bed and then raise the trailer high enough to clear the rails and drive out, leaving the hitch suspended from the trailer. This will give you more room to see under the hitch, along with enabling you to use yor truck. Good luck, it should be simple!
|
|
|
11-12-2018, 12:50 PM
|
#9
|
Montana Master
Join Date: Jul 2014
Location: Upstate NY
Posts: 1,788
M.O.C. #14547
|
Quote:
Originally Posted by Theunz
I think that the OP is stating that the handle IS moving, just not opening the jaws. If that is indeed the case than there is probably a pin or something that has come loose. You need to look under the hitch and see if you can find the problem. If necessary, you can remove the pins that attach the hitch to the bed and then raise the trailer high enough to clear the rails and drive out, leaving the hitch suspended from the trailer. This will give you more room to see under the hitch, along with enabling you to use yor truck. Good luck, it should be simple!
|
What the OP stated is exactly what has happened to mine. Either totaly level the TV and RV and it will come free - or move tthe combo back and forth .
__________________
Dave W
2014 Montana High Country 343RL (Sold!)
2011 Ford 6.7 Lariat CCLB (Went to PU Heaven)
2019 F150SC XLT SE Sport,w/full tow package
|
|
|
11-12-2018, 02:38 PM
|
#10
|
Montana Master
Join Date: Jul 2010
Location: Lake Havasu City AZ.
Posts: 1,811
M.O.C. #10552
|
Yikes it sounds like this brand hitch is problematic. I have an older Valley hitch that I have used at 45 degrees or better to hookup or to unhook. But I have a long bed truck.
__________________
Wayne and Ann Moore
2015 Ford F-350 King Ranch
Firestone air bags, bed saver.
Add 40 GAL tank in bed.
|
|
|
11-12-2018, 03:12 PM
|
#11
|
Montana Fan
Join Date: Jan 2018
Location: Boone
Posts: 311
M.O.C. #21011
|
Luckily you have one of the least problematic hitches on the market. And you have the luxury of locking the handle open while trying to unhitch. The FW and hitch are not agreeing with each other. Open the handle, install the little pin to hold the handle open, remove all pressure from the truck and FW. Sometimes, backing up first will release it. I’ve had it happen before on our previous B&W. Once you get it released, remove the whole head of the hitch and soak it down with penetrating oil, and grease everything. Mine never did it again after oiling it down. Good luck.
__________________
2018 Montana HC 362RD
2016 Chevrolet 3500 Duramax HD SRW
|
|
|
11-12-2018, 09:07 PM
|
#12
|
New Member
Join Date: Sep 2018
Location: Bethalto
Posts: 9
M.O.C. #22699
|
I was a truck driver for 40 years. I would set the trailer brakes while moving forward to tighten the king pin against the jaws of the fifth wheel. This stopped idiots from being able to pull the fifth wheel lever. Same on campers. Just back up and pull forward to release the pressure off of the king pin.
|
|
|
11-12-2018, 10:45 PM
|
#13
|
Montana Fan
Join Date: Apr 2014
Location: Eureka
Posts: 276
M.O.C. #14208
|
You were right on. The hitch was in a bind. Back and Forward it released. Thanks for the reply.
Jim
|
|
|
11-12-2018, 10:54 PM
|
#14
|
Montana Fan
Join Date: Apr 2014
Location: Eureka
Posts: 276
M.O.C. #14208
|
B & W Hitch
I did call B & W Tech Line and the gentleman said this is not uncommon. He recommended opening the handle and put the pin in the hole that will hold it open. Back up and then pull forward. It worked perfect and released. Thanks for all of the helpful answers.
Jim
|
|
|
11-13-2018, 08:03 AM
|
#15
|
Montana Master
Join Date: Dec 2009
Location: Sebring
Posts: 3,659
M.O.C. #9969
|
Actually that's the sign of a good hitch, nice and tight vs the ones that release very easily and the King Pin chucks back and forth in the loose Jaws.
__________________
Michelle & Ann
2018 Chevy 3500HD High Country DRW 4X4 Crew Cab w/Duramax/Allison, Formally 2010 Montana 2955RL, Now Loaded 2016 SOB, Mor/ryde IS, Disc Brakes & Pin Box, Comfort Ride Hitch, Sailun 17.5 Tires.
|
|
|
11-13-2018, 08:15 AM
|
#16
|
Montana Master
Join Date: Oct 2004
Location: Salem
Posts: 7,550
M.O.C. #2283
|
B & W needs to redesign their hitch. The jaws are forced closed with the handle. The jaws also need to be forced open with the handle. A simple redesign that would help when this occurs.
Lynwood
|
|
|
11-13-2018, 03:57 PM
|
#17
|
Montana Master
Join Date: Apr 2016
Location: Auburn
Posts: 879
M.O.C. #18474
|
Quote:
Originally Posted by mlh
B & W needs to redesign their hitch. The jaws are forced closed with the handle. The jaws also need to be forced open with the handle. A simple redesign that would help when this occurs.
Lynwood
|
I disagree as once the handle is closed, you really don't have to put the pin in it to keep it closed due to it will NOT open unless someone releases the pressure AND pulls the handle to the open position. More of a safety feature. In all the miles I've towed with it, it's happened less than 5-6 times.
__________________
2020 Montana 3790RD Legacy EditionOnan, TST TPMS, TrailAir pin, Discs,
2013 F350 DRW 4x4 CC LBViair 10007, Ride-Rites, Westin HDx, 12k Smittybilt
|
|
|
11-13-2018, 04:29 PM
|
#18
|
Montana Fan
Join Date: Apr 2014
Location: Eureka
Posts: 276
M.O.C. #14208
|
B&W hitch
Golfmedik, not sure if I agree with that last comment. You said you really don’t have to put the pin in it because the pressure will keep the jaws closed. I had a acquaintance that drove their vehicle with out putting the pin in it. Went quite awhile and probably hit a bump and it was enough to open the jaws. It was ugly.
Jim Bonhote
|
|
|
11-13-2018, 04:30 PM
|
#19
|
Montana Master
Join Date: Oct 2004
Location: Salem
Posts: 7,550
M.O.C. #2283
|
Quote:
Originally Posted by Golfmedik
I disagree as once the handle is closed, you really don't have to put the pin in it to keep it closed due to it will NOT open unless someone releases the pressure AND pulls the handle to the open position. More of a safety feature. In all the miles I've towed with it, it's happened less than 5-6 times.
|
I don’t think I made myself clear. This isn’t a safety issue. This has nothing to do with the pin to keep the jaws closed. Now when the handle is pulled it closes the jaws. Fix the handle so when it is pulled forward the jaws haft to open.
I camp in some rough places where some people wouldn’t take their truck. My camper can get the hitch in such a bind that it is almost impossible to get it unhooked. Having the hitch jaws designed where they had to open would sure be a help. At times all you can do to get unhooked is to raise the landing gear move a short distance and try again.
Lynwood
|
|
|
11-13-2018, 06:19 PM
|
#20
|
Montana Master
Join Date: Oct 2014
Location: Hagerstown
Posts: 866
M.O.C. #16013
|
gone and forgotten
This has happen to me one to many times, Bought the one with no moving parts to bind. I think it was raining and the wife asking if the water was on yet.
__________________
2018.5 3791 Rear Den Montana, on the lake no 3rd A/C, Mini Split, just do it
Electric Brakes ..... Disk Brakes, it`s the only way
F350 Ford Dually 4:10`s w/bags (payload 5595 lbs) Sumo Springs 63 gal aux tank
Reese Goosebox Mor/Ryde SRE 4000 X Factors Monroe shocks.... real smooth ride
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|