|
04-02-2018, 07:50 PM
|
#1
|
Montana Master
Join Date: May 2017
Location: new caney
Posts: 1,050
M.O.C. #19873
|
Brass quick connect fittings.
I know Home Depot and Lowe's sells quick connect fittings but where have any of you bought good quality brass quick connect fittings for the water hose and convenience center. I want to change everything to quick connect.I have found several places on-line but want good quality. Thanks.
|
|
|
04-02-2018, 08:18 PM
|
#2
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
bought all of mine from Do-it-Best, but they have changed recently to crap so, when I need some more I'll be in the search also.
|
|
|
04-02-2018, 10:10 PM
|
#3
|
Site Team
Join Date: Oct 2005
Location: Carmichael - CA
Posts: 7,365
M.O.C. #4831
|
I had bought a bunch of them in Quartzsite many years ago. No one there carries them any longer (the cheap plastic ones replaced them). I did find the same type on Amazon. Be aware that each manufacturer's connector is different from most all others.
Amazon Link
__________________
Carl (n Susan)
There is more to life than fuel mileage.
2012 Montana 3700RL Big Sky Package towed by a 2015 Ford F350 6.7L PSD 4WD CC LWB
|
|
|
04-02-2018, 10:22 PM
|
#4
|
Montana Master
Join Date: May 2016
Location: Cuyahoga Falls
Posts: 699
M.O.C. #18572
|
I got all of mine from CW. So far, so good.
__________________
ATC/NAC Jerry A. Burkholder, USN (RET.)
Rule #1. The Chief is always right.
Rule #2. When in doubt, refer to rule #1.
|
|
|
04-02-2018, 10:28 PM
|
#5
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,700
M.O.C. #12947
|
I use the brass ones I purchased from Lowes some time back. I find an occasional coating of silicone plumbers grease on the O-ring helps maintain the seal. I have also had to replace the O-rings on several of them. https://www.lowes.com/pd/Yardsmith-Y...r-Set/50328307
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
04-02-2018, 11:09 PM
|
#6
|
Seasoned Camper
Join Date: Dec 2015
Location: Pacheco
Posts: 69
M.O.C. #18133
|
Ace hardware has good connectors and replacement washers when thy leak.
I also use the red soft plastic fittings from camping world that have a rubber washer all the way through them. It’s like a stop leak fitting. Usually in a bucket near the cash register.
__________________
Mike and Karol
2015 Montana 3610
2014 Chevy 3500 dually
Full time since 2015
|
|
|
04-03-2018, 05:14 AM
|
#7
|
Montana Master
Join Date: Aug 2009
Location: Grand Rapids
Posts: 1,896
M.O.C. #9561
|
Do a google, lots out there
|
|
|
04-03-2018, 05:58 AM
|
#8
|
Montana Master
Join Date: Feb 2012
Location: Lake Gaston
Posts: 8,773
M.O.C. #12156
|
Been using for years. Bought my last set on Amazon about six months ago.
__________________
Mike and Lorraine
2002 3655 FL, 2005 3650RK
2010 3665RE, 2015 3910FB
F350 crew cab dually 6.7
|
|
|
04-03-2018, 06:04 AM
|
#9
|
Montana Master
Join Date: Jul 2014
Location: Upstate NY
Posts: 1,788
M.O.C. #14547
|
Most of the big box stores are now selling brass colored aluminum fittings that will corrode and fail fairly quickly (one summer season for one set I used) I bought a couple sets from AM Leonard which though pretty expensive have worked well, especially the pair on the 3/4" macerator discharge hose.
https://www.amleo.com/leonard-quick-...tors/p/VP-58X/
__________________
Dave W
2014 Montana High Country 343RL (Sold!)
2011 Ford 6.7 Lariat CCLB (Went to PU Heaven)
2019 F150SC XLT SE Sport,w/full tow package
|
|
|
04-03-2018, 09:26 AM
|
#10
|
Montana Master
Join Date: Oct 2017
Location: Bee Branch
Posts: 2,620
M.O.C. #20693
|
I got mine at Lowes and found same at Wal Mart. They are brass but you have to be careful not to over tighten or the rubber washer pushed out. I am on lookout for better design
__________________
James & Irene Wilson
Bee Branch, AR.
2017 Ram 1 ton diesel duallyCrew Cab/Long Bed
2018 Montana High Country 381TH Garage Full of Toys
|
|
|
04-03-2018, 10:32 AM
|
#11
|
Montana Master
Join Date: Apr 2006
Location: Mesa az
Posts: 2,952
M.O.C. #5651
|
Not to hijack the thread, but I have considered these. However, the connector in the wall seems pretty flimsy and made of plastic. I worry about these breaking when trying to connect or disconnect. When I have looked at these, it seems you have to put a lot of pressure on the connection to push/pull the two ends together and could break something. Comments?
__________________
Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
|
|
|
04-03-2018, 10:33 AM
|
#12
|
Montana Master
Join Date: May 2017
Location: new caney
Posts: 1,050
M.O.C. #19873
|
Quote:
Originally Posted by Dave W
Most of the big box stores are now selling brass colored aluminum fittings that will corrode and fail fairly quickly (one summer season for one set I used) I bought a couple sets from AM Leonard which though pretty expensive have worked well, especially the pair on the 3/4" macerator discharge hose.
https://www.amleo.com/leonard-quick-...tors/p/VP-58X/
|
A.M. Leonard is what i have been looking at. I found a set at another place that is U.S. made but even more expensive than A.M. Leonard. I called Leonard and they are made in China as well as just about everyone elses. Leonard is 13.89 per set and i would need 2 sets plus another male fitting so i would probably buy 3 sets. Hopefully these will be better than the other China made fittings as Sailuns are better than the other China made tires.
|
|
|
04-03-2018, 02:18 PM
|
#13
|
Montana Master
Join Date: Oct 2017
Location: Bee Branch
Posts: 2,620
M.O.C. #20693
|
Quote:
Originally Posted by twindman
Not to hijack the thread, but I have considered these. However, the connector in the wall seems pretty flimsy and made of plastic. I worry about these breaking when trying to connect or disconnect. When I have looked at these, it seems you have to put a lot of pressure on the connection to push/pull the two ends together and could break something. Comments?
|
There was a recent thread where folks are replacing the plastic OEM panel fittings with superior brass. I highly recommend that upgrade. Also using a 45 degree hose fitting will reduce strain on the connection. To reduce stress while coupling simply hold the 45 with one hand and push hose end with other
__________________
James & Irene Wilson
Bee Branch, AR.
2017 Ram 1 ton diesel duallyCrew Cab/Long Bed
2018 Montana High Country 381TH Garage Full of Toys
|
|
|
04-03-2018, 02:19 PM
|
#14
|
Montana Master
Join Date: Oct 2017
Location: Bee Branch
Posts: 2,620
M.O.C. #20693
|
Quote:
Originally Posted by Texan
A.M. Leonard is what i have been looking at. I found a set at another place that is U.S. made but even more expensive than A.M. Leonard. I called Leonard and they are made in China as well as just about everyone elses. Leonard is 13.89 per set and i would need 2 sets plus another male fitting so i would probably buy 3 sets. Hopefully these will be better than the other China made fittings as Sailuns are better than the other China made tires.
|
If your like me ya gotta add more sets to setup black water flush lines too....
It never ends does it....
__________________
James & Irene Wilson
Bee Branch, AR.
2017 Ram 1 ton diesel duallyCrew Cab/Long Bed
2018 Montana High Country 381TH Garage Full of Toys
|
|
|
04-03-2018, 03:29 PM
|
#15
|
Montana Master
Join Date: Jul 2014
Location: Upstate NY
Posts: 1,788
M.O.C. #14547
|
Quote:
Originally Posted by mtlakejim
There was a recent thread where folks are replacing the plastic OEM panel fittings with superior brass. I highly recommend that upgrade. Also using a 45 degree hose fitting will reduce strain on the connection. To reduce stress while coupling simply hold the 45 with one hand and push hose end with other
|
I use a 45 on the water inlet and a 90 on the flusher, both with quick connects. These fittings on that water panel sure are flimsy and those angled fittings take much of the strain off.
I looked at the back side of that water panel considering replacing the plumbing with either 1/2" copper or PVC and decided that would be a project way down on the bottom of my list of projects. There are times that the old Newmar Kountry Aire with all copper plumbing looks good
__________________
Dave W
2014 Montana High Country 343RL (Sold!)
2011 Ford 6.7 Lariat CCLB (Went to PU Heaven)
2019 F150SC XLT SE Sport,w/full tow package
|
|
|
04-03-2018, 05:22 PM
|
#16
|
Montana Master
Join Date: May 2017
Location: new caney
Posts: 1,050
M.O.C. #19873
|
Quote:
Originally Posted by mtlakejim
If your like me ya gotta add more sets to setup black water flush lines too....
It never ends does it....
|
I have the 45 degree for city water and black tank. I just need a 45 degree for the fresh water then i will install the quick connect to all 3 and that should put me in business. Improvements are never ending. I ordered me some extra o -rings for the male and female connectors at the same time as ordering the connectors. Now i just need to order my valterra valves and install them and maybe i can let my pocket book take a break. I might try to install the valves before i have my rotator cuff surgery as this will shut me down for several weeks if not months. I sure do a lot of improvements for someone who is very part-time.I don't think i could afford full time with what i spend lol.
|
|
|
04-03-2018, 05:35 PM
|
#17
|
Site Team
Join Date: Sep 2017
Location: Oro Valley
Posts: 3,932
M.O.C. #20477
|
I use short leader hoses that will extend out the opening in the bottom to connect to longer hoses and then stow up in the convenience center for travel and storage. Only connect them to the inlets once and easy to hook up to longer service hoses.
__________________
Zack and Donna plus Millie and Ranger
2018 3160RL
"Life is too short to stay indoors, enjoy the ride!"
|
|
|
04-03-2018, 06:25 PM
|
#18
|
Montana Master
Join Date: May 2017
Location: new caney
Posts: 1,050
M.O.C. #19873
|
Quote:
Originally Posted by AZ Traveler
I use short leader hoses that will extend out the opening in the bottom to connect to longer hoses and then stow up in the convenience center for travel and storage. Only connect them to the inlets once and easy to hook up to longer service hoses.
|
Sounds like a good idea. I would only need the leader hoses to extend out about 6'' at most from the bottom
|
|
|
04-03-2018, 06:43 PM
|
#19
|
Montana Fan
Join Date: Feb 2016
Location: Brookings
Posts: 313
M.O.C. #18275
|
ACE has good brass fittings for quick disconnect.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|