|
11-06-2007, 03:05 PM
|
#1
|
Montana Master
Join Date: Jan 2006
Location: South
Posts: 2,499
M.O.C. #5140
|
Check Valve Stuck
For those of you who don't know me, I'm 6-02 and 265 pounds - not a weakling.
I cannot get the check valve unscrewed from the hot water heater. Any suggestions? And, yes, I'm turning it in the right direction...
|
|
|
11-06-2007, 03:11 PM
|
#2
|
Montana Master
Join Date: Nov 2005
Location: Campbell River
Posts: 970
M.O.C. #4976
|
If you can take the pipe off first.
Try a Socket on an impact gun ? light bursts to loosen it.
J&D
|
|
|
11-06-2007, 03:25 PM
|
#3
|
Montana Master
Join Date: Oct 2006
Location: _
Posts: 5,238
M.O.C. #6337
|
Al has retired for the night, but the way I remember it, there was a bit of mumbling and growling involved in the removal of this valve last winter in Mission. May have been the use of a "breaker bar"??? Accompanied by a few scrapes on the ole knuckles. I don't remember if he used any kind of lubricant to "loosen" it. I know it was not easy. And, I know that is not what you wanted to hear...
|
|
|
11-07-2007, 12:38 AM
|
#4
|
Montana Master
Join Date: Jul 2006
Location: K.C.
Posts: 11,731
M.O.C. #5980
|
Good suggestions, all. I can just add that heat, then cold applied works well. If you can get dry ice, pack the nut as good as you can with it, then immediately loosen the nut. As my wise friend John stated, the impact wrench is great, I don't leave home without mine. This cold application Worked for me in the Machine shop getting parts off the old Diesel Subs. When you put it back on, or the new one, use a small amount of pipe dope, or teflon tape on the threads, after using a wire brush on the female threads.
Good luck buddy.
Ozz
|
|
|
11-08-2007, 11:25 PM
|
#5
|
Montana Master
Join Date: Jul 2004
Location: Conover
Posts: 995
M.O.C. #1832
|
Like Ozz said heat/cold works well. If you can get to it with plumbers torch heat it up good then poor cold water over it she will loosen up. Impact might work but don't see how you will get it in there enough unless you have long enough extension to get to it.
|
|
|
11-09-2007, 12:33 AM
|
#6
|
Montana Master
Join Date: Jul 2006
Location: K.C.
Posts: 11,731
M.O.C. #5980
|
He did get it off, and Michael installed a filter in there as well, good pictures of the work, real slick job. It must be on another post.
|
|
|
11-09-2007, 06:49 AM
|
#7
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
I'd like to see those pictures.
I need to replace that valve in ours as it is still buzzing. We got a new valve the other day. When I changed the one on our 3295rk, it was no problem removing the old one. I hope I don't experience the problems Michael had. I don't know where the w/h is in his 2006 3400 but ours is in the kitchen island where it attaches to the wall. There is just one small access panel on each side. And I mean small. I may have to enlarge it and get a new covering panel if I can't get this thing apart. I'll give it a try next week or this weekend.
|
|
|
11-09-2007, 04:09 PM
|
#8
|
Montana Master
Join Date: Jan 2006
Location: South
Posts: 2,499
M.O.C. #5140
|
Steve,
Our HWH is in the same place - I removed the cabinet bottom to get access to the HWH. I had previously reinforced the bottom and made sure to reinstall in such a way that I could get to the HWH if needed. See this link:
http://www.montanaowners.com/forums/...ad.php?t=25288
|
|
|
11-10-2007, 09:19 AM
|
#9
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
Quote:
quote:Originally posted by snfexpress
Steve,
Our HWH is in the same place - I removed the cabinet bottom to get access to the HWH. I had previously reinforced the bottom and made sure to reinstall in such a way that I could get to the HWH if needed. See this link:
http://www.montanaowners.com/forums/...ad.php?t=25288
|
Thanks, Michael. That will be VERY helpful. I had not noticed the screws in the cabinet floor but that will make access much easier.
I see your water connections (from outside) are right in the same area. Mine are in the basement so I'll need to install my filter behind the connection center in the basement.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|