|
08-04-2014, 06:48 AM
|
#1
|
Montana Fan
Join Date: Jul 2011
Location: Wichita
Posts: 113
M.O.C. #11612
|
Landing gear
2012 3400. Passenger side landing gear isn't raising or lowering. All weight on drivers side to lift. Is this something I can fix. I looked quickly and couldn't see an obvious access to the leg.
|
|
|
08-04-2014, 07:54 AM
|
#2
|
Montana Master
Join Date: Feb 2005
Location: Haysville
Posts: 4,261
M.O.C. #3085
|
The curb side legs are easy to remove while your fiver is still hooked to your truck. Take the bolt out of the driveshaft and the two bolts out of the frame mounts inside your propane compartment. The leg will simply pull out the bottom. Sometimes you'll have to remove the leg extension prior to removing the leg itself depending on terrain. There was a "sticky" on the workings of the leg itself, but I can't find it. Assuming your legs are manufactured by Venture ... here's a link to an exploded view.
http://www.venturemfgco.com/admin/up...0explosion.pdf
PS Make sure it isn't something as simple as the bolt in the cross shaft has sheared before you remove the leg.
|
|
|
08-04-2014, 08:49 AM
|
#3
|
Montana Master
Join Date: Oct 2007
Location: Land O Lakes
Posts: 2,751
M.O.C. #7753
|
Check the shear pin before anything else. you have a round shaft connecting to a square tubing. There should be a pin at either end of the square shaft between 2 and 6 inches in from the end. The shear pins are basically 1/4 x20 bolts..
|
|
|
08-12-2014, 03:48 PM
|
#4
|
Established Member
Join Date: Jun 2014
Location: St. Louis
Posts: 12
M.O.C. #14324
|
Had the same problem. A 1/4 bolt fell out of the drive shaft at the back of the motor. replaced bolt with a nyloc nut so I don't loose it again.
|
|
|
08-12-2014, 04:29 PM
|
#5
|
Montana Master
Join Date: Jun 2004
Location: Benson
Posts: 3,121
M.O.C. #1658
|
Hawkpat, did you ever fix your problem?
|
|
|
08-12-2014, 04:48 PM
|
#6
|
Montana Master
Join Date: Dec 2007
Location: Kansas City, Missouri
Posts: 2,707
M.O.C. #7992
|
I'm kind of late to this topic but I had the same thing happen when at the Central Plains Rally only on the street side. On mine the 1020-08 Spirol Pin on the drawing dieselguy provided had fallen out. Could tell as the shaft through the leg was turning but the bevel gear was not. Rondo had a rebuild kit with the Spirol Pin. Lucky for me the slot in the gear was at about 10 o'clock position so I could insert a punch and had someone bump the switch until the punch lined up with the hole in the shaft. Once aligned just drove the roll pin in. Jim
__________________
2006 3000RK
2009 Ram 2500
|
|
|
08-13-2014, 05:15 AM
|
#7
|
Montana Fan
Join Date: Jul 2011
Location: Wichita
Posts: 113
M.O.C. #11612
|
It was the shear pin. Thanks for the help
|
|
|
08-13-2014, 12:10 PM
|
#8
|
Montana Master
Join Date: Jun 2004
Location: Benson
Posts: 3,121
M.O.C. #1658
|
Glad to hear it was an easy fix and thanks for letting us know
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Which Landing Gear
|
lundwc16 |
Montana Problems, Problem Solving & Technical Help |
5 |
01-11-2016 02:12 AM |
Landing Gear Gear Maintenance
|
1retired06 |
General Discussions about our Montanas |
6 |
02-28-2012 08:21 AM |
Landing gear
|
ALAN |
Montana Problems, Problem Solving & Technical Help |
3 |
10-14-2009 05:32 PM |
Landing gear--is the gear stripped?
|
David and Jo-Anna |
Montana Problems, Problem Solving & Technical Help |
16 |
04-27-2008 05:47 PM |
Landing Gear Mod
|
Bill and Lisa |
Additions & Improvements |
13 |
07-18-2007 12:50 AM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Disclaimer:
This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.
All times are GMT -6. The time now is 04:42 AM.