|
08-28-2013, 07:07 PM
|
#1
|
Seasoned Camper
Join Date: Mar 2009
Location: BOX ELDER
Posts: 90
M.O.C. #9158
|
Axle and Tire wear
Still having problem tire wear. Had the rear axle replaced in Anchorage and two new G614 tires installed. After about two hundred miles on Alaska roads I noticed that the left rear tire was leaning out and was showing wear on the inside. Now in Whitehorse the axle will be removed and straightened if bent.
Here is my question: before leaving on this Alaskan journey, Camping World in Burlington WA welded a couple of steel bars behind the rear axle to improve stability. I am thinking that this is making the suspension rigs and perhaps transferring loads to wear to the axle and increasing stress on it.
I am thinking about having the bars removed when the axles gets reinstalled. Appreciate your thoughts on the stabiliazer bars.
|
|
|
08-29-2013, 02:18 AM
|
#2
|
Montana Master
Join Date: Apr 2013
Location: Arroyo City
Posts: 3,110
M.O.C. #13395
|
Where were the bars attached to the axels?
|
|
|
08-29-2013, 02:23 AM
|
#3
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
Many folks have installed X Factor, which are in essence metal bars running between the frame members near the axles. Those of us who have Mor/Ryd IS have a couple large tubes welded across in approximately the same area. Both ways of doing it haven't resulted in folks having tire wear problems, reported here anyway. I can't imagine that's your problem unless the frame was bent when they welded them or some other weird thing is going on.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
08-29-2013, 02:49 AM
|
#4
|
Site Team
Join Date: Aug 2007
Location: Omaha
Posts: 6,754
M.O.C. #7560
|
If whoever you had put on the new axle did not align it and align it with the the front axle, there is your problem. If they did do this then I would say the new axle they put on is out of camber. I had the problem but my wear was on the front axle after we changed out the rear one. Took it into a reputable axle shop here and they aligned the axles again and also put the camber back in the front axle. This was a whole lot cheaper than having the axle replaced--about $148 total. Hope you can get your problem figured out because replacing tires is not cheap especially the G614s.
|
|
|
08-29-2013, 03:09 AM
|
#5
|
Montana Master
Join Date: Feb 2005
Location: Haysville
Posts: 4,261
M.O.C. #3085
|
I'm thinking along the same lines as Rondo ... if they simply bolted the new axle on your rig and said here you go ... they missed the important step of checking / adjusting the alignment. I can't comment on the "bars" welded to your frame, but like said, many of us use a version of the XFactor which is a beam(s) crosswise between the suspension mounts. Whitehorse business should not remove the axle to "straighten" it. All larger axles have a slight bow upward in the middle to create camber. All larger axles have the spindles angled ever so slightly forward to account for toe-in. You need to find a shop that has the equipment to check alignment as the fiver sits on both axles. The weight of your fiver will change the axle measurements as compared to an axle just lying on a pair of saw horses.
|
|
|
08-30-2013, 02:37 PM
|
#6
|
Montana Master
Join Date: Aug 2012
Location: Northport
Posts: 624
M.O.C. #12724
|
Don't know anything about this product but picked up a information pamphlet the other day at dealer. Don't know if this is something that might help. www.themobileoutfitters.com .Look under products for correct track.
__________________
Paul Northport,AL W4XH
2013 358 RLT Mountaineer
2008 Silverado Duramax
|
|
|
08-30-2013, 03:47 PM
|
#7
|
Montana Master
Join Date: Feb 2005
Location: Haysville
Posts: 4,261
M.O.C. #3085
|
I'm not a fan of the aftermarket version of this product. It in effect increases the length of your spring eye frame mounts (read possibly more stress) and ultimately raises your fiver up an inch or two. Our frame mounts are not exactly a "Tower of Power" to start with. I'm sure the company will explain all of this away, but ........ Any reputable alignment shop will get your axles squared away without this kit.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|