|
|
06-16-2019, 09:31 AM
|
#21
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
No sir - the main tripped if I tried to turn the tripped breaker on. That action would shut the back unit off too, as it tripped the main. As long a the tripped breaker stayed off, the rear unit continued to run. Mine has the main in the middle of the panel.
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
06-16-2019, 09:40 AM
|
#22
|
Montana Master
Join Date: Oct 2006
Location: McKinney
Posts: 7,159
M.O.C. #6433
|
OK, that makes sense. Apparently a dead short to ground on that one circuit. That screw must have been grounding that circuit to the panel metal case or other ground or neutral point. Hopefully removing the screw solved the problem. But no real way of knowing what or if any damage was done without removing the panel to see the back side.
__________________
Bill & Patricia
Riley, our Golden
2007 3075RL (recently sold, currently without)
|
|
|
06-16-2019, 09:49 AM
|
#23
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
I suppose that when the screw went in, the circuit grounded and tripped the breaker immediately - that is why it didn't shock me? I think the take-home message here is not to screw anything into the bathroom wall behind the breaker box! This is a good place for Command adhesive strips.
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
06-16-2019, 11:32 AM
|
#24
|
Montana Master
Join Date: Oct 2017
Location: Bastrop
Posts: 2,892
M.O.C. #20753
|
Quote:
Originally Posted by MaxwellD
I suppose that when the screw went in, the circuit grounded and tripped the breaker immediately - that is why it didn't shock me? I think the take-home message here is not to screw anything into the bathroom wall behind the breaker box! This is a good place for Command adhesive strips.
|
That and keep the screws less than 6 inches
__________________
Mocha, one-eyed toothless, hurricane survivor, Pirate dog
2019 20th Anniversary Edition 3701LK
B&W 20K for Ford OEM Puck
2018 Ford F-350 Lariat CCLB PSD DRW KJ5CQH
|
|
|
06-16-2019, 01:49 PM
|
#25
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
Quote:
Originally Posted by jeffba
That and keep the screws less than 6 inches
|
It is a heavy-duty spray hose.
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
06-23-2019, 03:05 PM
|
#26
|
Seasoned Camper
Join Date: Jan 2019
Location: Conway
Posts: 74
M.O.C. #23367
|
Check all your lugs at your shore power supply.
Had mine trip 2 weeks ago.
One leg lug was a 1/2 turn loose .
Tighten it up and reset with no problems yet.
|
|
|
06-23-2019, 07:09 PM
|
#27
|
Montana Fan
Join Date: Sep 2016
Location: Fargo
Posts: 213
M.O.C. #19032
|
If you ran a screw through the romex, and you pull the screw out... you still have a compromised electrical cable in your wall. That needs attention weather removing the screw cures the breaker tripping or not. Time to open up the wall somehow and put in a j-box and splice it properly. I would not be comfortable with that wire compromised like that.
__________________
2004 Montana 3295RK 2019 Ram / Cummins 2500 Summer season weekend warrior
|
|
|
06-23-2019, 07:36 PM
|
#28
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
Quote:
Originally Posted by Mark7
If you ran a screw through the romex, and you pull the screw out... you still have a compromised electrical cable in your wall. That needs attention weather removing the screw cures the breaker tripping or not. Time to open up the wall somehow and put in a j-box and splice it properly. I would not be comfortable with that wire compromised like that.
|
Neither would I be comfortable with that. But, a qualified electrician told me that most likely the screw tip hit the back of the metal box encasing the breakers, and at that point, grounded instantly. Since it was out of the circuit, the breaker tripped. It is doubtful that the screw went through romex from my understanding. But your point is a good one. When I finish this trip, I may tear into the wall - depending on how much else may go wrong. So far, so good !
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
06-23-2019, 07:39 PM
|
#29
|
Montana Fan
Join Date: Sep 2016
Location: Fargo
Posts: 213
M.O.C. #19032
|
My error... must have missed that point scanning the thread! Not going to second guess an electrician!
__________________
2004 Montana 3295RK 2019 Ram / Cummins 2500 Summer season weekend warrior
|
|
|
06-23-2019, 07:40 PM
|
#30
|
Montana Fan
Join Date: Oct 2017
Location: Tyler
Posts: 186
M.O.C. #20704
|
Quote:
Originally Posted by KJT
Check all your lugs at your shore power supply.
Had mine trip 2 weeks ago.
One leg lug was a 1/2 turn loose .
Tighten it up and reset with no problems yet.
|
Not quite sure what you are referencing. The problem seems to be resolved for now. I may not have to do that
__________________
Maxwell and Beverly Dow
2018 3730FL 2020 Ram 3500 Dually SWB
"Prairie Schooner"
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|