Go Back   Montana Owners Club - Keystone Montana 5th Wheel Forum > GENERAL DISCUSSIONS > General Discussions about our Montanas
Click Here to Login

Reply
 
Thread Tools Display Modes
 
Old 07-31-2014, 08:11 AM   #1
twindman
Montana Master
 
twindman's Avatar
 
Join Date: Apr 2006
Location: Mesa
Posts: 1,232
M.O.C. #5651
complete battery disconnect

I think the battery negative connects to the frame. So if I put in a switch there, is that the proper way to turn off everything???
I have a marine switch that has connections for 2 sets of batteries separately or singly or off. So I think if I run the negative wires from both battery sets to this switch, it should work.
Any comments or problems you see???
Thanks.
__________________

Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
twindman is offline   Reply With Quote
Old 07-31-2014, 12:15 PM   #2
bigred715
Montana Master
 
Join Date: Dec 2005
Location: Eugene
Posts: 872
M.O.C. #5091
When I disconnect for a period of time I ALWAYS take off the positive and leave the negative hooked up. This has worked for me on the trailer and the car while I am in Arizona for 3 months.
bigred715 is offline   Reply With Quote
Old 07-31-2014, 12:21 PM   #3
jlb27537
Montana Master
 
Join Date: Jan 2013
Location: Depends on temps
Posts: 1,648
M.O.C. #13157
The battery disconnect is usually in the positive lead.

Jim
jlb27537 is offline   Reply With Quote
Old 07-31-2014, 02:31 PM   #4
DQDick
Montana Master
 
DQDick's Avatar
 
Join Date: Jun 2011
Location: Wilsey
Posts: 15,405
M.O.C. #11455
Positive is also the way I've always done it.
__________________
Dick and Joyce, Wilsey, KS & Lakewood, NM
2017 3720 RL
2017 3500 Dodge Maxi Cab
IS and Disk Brakes, 3rd AC, Bathroom door mod, etc.
DQDick is offline   Reply With Quote
Old 07-31-2014, 03:08 PM   #5
bncinwv
Montana Master
 
Join Date: Feb 2007
Location: Winfield
Posts: 7,316
M.O.C. #6846
If you are installing a dual battery system to a dual battery marine isolator switch, the way I wired mine is as follows: the individual positive (red) leads go to the switch positive posts. The negative (black) from the switch then goes to one battery negative post and the two positives of the batteries are wired together, then the negative from the last battery goes to the frame. This will allow you to use one or the other or both (if they are similar batteries). It is a good idea to use the same type batteries as I do not believe the onboard charger will support different types. Check the manual to verify this.
Bingo
__________________

Bingo and Cathy - Our adventures begin in the hills of WV. We are blessed by our 2014 3850FL Big Sky (previous 2011 3750FL and 2007 3400RL) that we pull with a 2007 Chevy Silverado Classic DRW CC dually.
bncinwv is offline   Reply With Quote
Old 08-01-2014, 02:44 AM   #6
Phil P
Montana Master
 
Join Date: Mar 2011
Location: Okeechobee
Posts: 2,119
M.O.C. #11206
Hi

If you were trained by the US Army you would disconnect the positive cable. If you were trained by the US Navy you would disconnect the negative cable.

It just doesn’t make any difference so I put the fuse or disconnect switch where ever it is easiest to install.

A word of caution that really doesn’t have any relativity to the question I really recommend putting a 100 Amp fuse at the battery they are not that expensive and could save your trailer from one of the “mysterious” self igniting fires.

http://www.bluesea.com/products/5191...k_-_30_to_300A

Phil P
__________________
2009 Montana 3665RE
2009 Duramax 3500 DRW quad cab
personal web page https://www.sallyscoffees.com
If you get a page not available then remove the "s" after HTTP
Phil P is offline   Reply With Quote
Old 08-01-2014, 04:45 AM   #7
markmontana
Established Member
 
Join Date: Jul 2013
Location: Mesquite
Posts: 21
M.O.C. #13597
Phil's idea is what we did. Here is the amazon link

http://www.amazon.com/Blue-Sea-Syste...ery+fuse+block
markmontana is offline   Reply With Quote
Old 08-01-2014, 05:05 AM   #8
gjetzen
Montana Fan
 
Join Date: Aug 2007
Location: Andover
Posts: 236
M.O.C. #7542
If you were trained to be an auto mechanic like I was you would always disconnect the negative side(-). The positive is the side that will always spark upon disconnect, and if done at the battery can risk explosion. When replacing a DC battery in an RV, Boat or in an auto/truck the procedure is negative off first and on last! Also while I can't be 100% sure on an 5th wheel trailer, In boats and anything automotive the negative side (-) is always the side that is regulated, they will control the ground not the feed, it is safer and less expensive. Putting a switch of any kind on the positive side (+) of any circuit runs the risk of a voltage drop and some systems require a 12v power source to operate properly.
gjetzen is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Battery disconnect tracyclifton General Discussions about our Montanas 5 03-25-2015 04:05 PM
Battery Disconnect Lenny K Montana Problems, Problem Solving & Technical Help 6 08-16-2014 04:46 PM
When is the battery disconnect not a disconnect? jfaberna General Discussions about our Montanas 17 12-31-2013 04:39 AM
BATTERY DISCONNECT johncamtravel General Discussions about our Montanas 4 11-15-2013 08:51 PM
Battery Disconnect Montana_4699 General Discussions about our Montanas 2 10-30-2005 04:19 PM

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.


All times are GMT -6. The time now is 10:58 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.