|
10-03-2007, 10:18 AM
|
#1
|
Established Member
Join Date: Sep 2007
Location: pensacola
Posts: 15
M.O.C. #7657
|
Wheel Bearing
Do you have the wheel bearings repacked or put grease in the easy lube fittings? What is a good rate to have the wheel repacked. They told me hear $300.00 that seems high and I am tempted to just grease them. Thanks for the help
|
|
|
10-03-2007, 11:47 AM
|
#2
|
Montana Master
Join Date: Nov 2005
Location: cedar rapids
Posts: 703
M.O.C. #4962
|
There have some posts on this in the last few weeks. 200-300 is not out of line to have the dealer do it. What ever you do DO NOT PUMP GREASE INTO THE ZERK'S AT THE END OF THE AXLE OR DO NOT LET THE DEALER DO IT. What will happen is you will blow out the axle seals and then a whole lot of problems will happen that you don't want. Either you or the dealer should remove the hubs,knock out the bearings and pack them by hand and install new seals and remove the Zerk so as not to pump grease into the hub and blow the seals. Do it like in the olden days. You do not need to fill the hub with grease. Just pack the bearings.
|
|
|
10-03-2007, 02:51 PM
|
#3
|
Montana Master
Join Date: Apr 2007
Location: Frostproof
Posts: 512
M.O.C. #7125
|
I don't remember reading anywhere NOT TO GREASE USING THE GREASE ZERTS. I do remember reading not to use a power grease gun, but to use a hand gun. Read the Dexter info, or call them. If I remember correctly, one shot once a year, and a repacking by hand and seal replacement at 12000mi rings a bell, but check with Dexter. Kerry
|
|
|
10-03-2007, 02:51 PM
|
#4
|
Montana Master
Join Date: Sep 2006
Location: Wappingers Falls
Posts: 1,303
M.O.C. #6263
|
Agree with hazmic on this one. I'm a part timer and do mine every other year, pull drums, knock out rear bearings, clean up, check cups -n- cones for pitting, pack grease into cones, check shoes, wiring, reassemble, spin each one as I progress around rig and use an old brake controller w/harness I wired to check brake operation...on completion of last one...I'm ready to go into the wilderness!
|
|
|
10-03-2007, 03:14 PM
|
#5
|
Montana Fan
Join Date: Jul 2007
Location: No Telling
Posts: 207
M.O.C. #7430
|
Quote:
quote:Originally posted by kerry
I don't remember reading anywhere NOT TO GREASE USING THE GREASE ZERTS. I do remember reading not to use a power grease gun, but to use a hand gun. Read the Dexter info, or call them. If I remember correctly, one shot once a year, and a repacking by hand and seal replacement at 12000mi rings a bell, but check with Dexter. Kerry
|
Me too.
They are like Buddy Bearings used on boats, designed to accept grease from a hand operated grease gun. They are built to be lubbed that way.
|
|
|
10-03-2007, 04:39 PM
|
#7
|
Montana Master
Join Date: Jul 2006
Location: Liberty Lake
Posts: 2,310
M.O.C. #6088
|
With all of the post regarding packing wheel bearings, I have yet see any reference to the specific wheel bearing grease to use.
|
|
|
10-03-2007, 04:54 PM
|
#8
|
Montana Master
Join Date: Apr 2007
Location: Frostproof
Posts: 512
M.O.C. #7125
|
The Dexter manual I posted addresses this; pg48. Kerry
|
|
|
10-03-2007, 05:26 PM
|
#9
|
Montana Master
Join Date: Apr 2007
Location: Frostproof
Posts: 512
M.O.C. #7125
|
I corrected my previous web address for the direct link to the service manual. Kerry
|
|
|
10-03-2007, 05:33 PM
|
#10
|
Montana Master
Join Date: Apr 2007
Location: Frostproof
Posts: 512
M.O.C. #7125
|
|
|
|
10-03-2007, 06:42 PM
|
#11
|
Montana Master
Join Date: Jul 2007
Location: Merlin
Posts: 668
M.O.C. #7368
|
DONnANNIE, In kerry's post, the PDF link page 48 calls out the grease specifics, and Approved sources. Can't figure out how to copy and past it here, or I would.
|
|
|
10-04-2007, 05:30 AM
|
#12
|
Montana Master
Join Date: Nov 2004
Location: Arnold
Posts: 1,200
M.O.C. #2586
|
Very good and helpful info here! Thanks, all.
|
|
|
10-04-2007, 06:57 AM
|
#13
|
Montana Master
Join Date: Aug 2006
Location: Lone Tree
Posts: 5,615
M.O.C. #6109
|
The EZ lube hubs and available grease zerks tend to invite trouble. Because there is a zerk, folks want to grease it.
Two things happen - folks either pump too much grease in there and push the seal off the back, or they pump a little bit of grease way to often and they push the seal off the back. Once the seal is pushed back, the additional grease is going into the brake drum.
Unless you are backing your Montana into the lake to launch it 30-40 times a year, I don't think those bearings need a whole lot of attention. I tend to just leave them alone. I've been using the zerks moderately on my boat trailer for 14 years and I've never had to repack, nor have I blown a seal or lost a bearing/spindle (knock on wood). I pull and inspect every year. To me, the process of cleaning, repacking, and reassembling unecessarily actually increases the potential failure. The only problem I have ever had with a wheel bearing was when I repacked them every year.
|
|
|
10-04-2007, 03:04 PM
|
#14
|
Montana Fan
Join Date: Mar 2005
Location: Keystone Heights
Posts: 164
M.O.C. #3433
|
I do my Tana and truck bearings myself for two reasons. First I don't trust someone else to do them the way my Dad taught me. Clean them in diesel to get all the old grease out, then use a compressor to blow them out. Check the rollers for wear or any rough spots. Secondly, doing it myself, it gives me a chance to inspect the brakes and the under carriage. I always use synthetic bearing grease on the RV and on my truck. I get the seals at a local trailer supply store that sells parts for horse trailers etc. The seals are cheaper than Napa or Discount Auto and I think the quality is as good or better.
|
|
|
10-05-2007, 06:03 AM
|
#15
|
Montana Master
Join Date: Feb 2005
Location: Pagosa Springs
Posts: 3,711
M.O.C. #3120
|
Kerry,
Thanks for the great information.
|
|
|
10-05-2007, 08:22 AM
|
#16
|
Montana Master
Join Date: Aug 2004
Location: Cedar Rapids
Posts: 4,876
M.O.C. #1944
|
I agree with hazmic. The zerks are there to allow us to self lube. However, WE (me, and others) have a tendency to over lube. "One pump is good two must be better." What happens is you will blow out the seal, will get grease all over everything. Why do they put the EZ Lubes on the rigs? Because we will buy them. I also agree with another poster that you won't find anywhere it says not to use the self lubes. If you can be frugal (and I mean frugal) with the grease you're okay. But believe me, almost everyone over lubes. As for the bearing buddies on boat trailers, they are there, not to hold the grease, but rather to prevent water from getting to the bearings when the boat trailer is backed down the ramp to put the boat in the water. The EZ lubes are not much different, other than to allow you to use your grease gun. Take it from one who has had the experience, don't use the EZ lubes. I've had mine removed and chalked it up to another experience.
But people should do what they see fit to do. If in fact they experience the same thing I did, then they can't say that they weren't warned.
Orv
|
|
|
10-05-2007, 08:40 AM
|
#17
|
Montana Master
Join Date: Aug 2006
Location: Lone Tree
Posts: 5,615
M.O.C. #6109
|
I was just looking at the Dexter manual posted by Kerry, and it says to pump with the grease gun until you see fresh grease coming back into the outer ring! Not this kid !! - If that seal in the back fails, fresh grease will not be seen until the entire brake drum is filled. I think the instructions only work in theory, but never really work in practice .
|
|
|
10-05-2007, 10:17 AM
|
#18
|
Montana Master
Join Date: Apr 2007
Location: Frostproof
Posts: 512
M.O.C. #7125
|
I will say this; we use this (Dexter Procedure) in our shop, and so far we haven't had any problems. We don't use a power grease gun. Kerry
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|