|
12-02-2004, 07:47 AM
|
#1
|
Montana Fan
Join Date: Jun 2004
Location: CHEWELAH
Posts: 318
M.O.C. #1654
|
Water tank wont fill,any suggestions?
By actual timing,one 2 gal. bucket takes 2 minutes, I can only get 12 gal of water into my tank befor the vent starts spurting and the water comes jetting out the fill hole. I'm wondering if the tank could be colapsed? does anyone else have this problem? Dave
|
|
|
12-02-2004, 07:56 AM
|
#2
|
Montana Fan
Join Date: May 2003
Location: Ottawa Lake
Posts: 307
M.O.C. #321
|
Dave are you sure the fresh water tank was completely empty when you started to fill it. If you are going by the tank levels on the monitor panel they may be off, and another possibility is the air has to come out of the tank as water goes in make sure you don't have a line that has a bend in it. Just a thought,Roman
|
|
|
12-02-2004, 08:17 AM
|
#3
|
Montana Master
Join Date: Oct 2004
Location: Ore City Texas
Posts: 1,648
M.O.C. #2224
|
Dave, That "water jetting back out" is standard procedure for me. I don't think it should be but it is. Seems the vent does not properly allow the air to escape. Since I do this at home before leaving on trips, I just let it 'gush' then start filling again. My practice is to fill the tank only to the first 1/3 light on the gage, as I do not like to carry the weight of full tanks. Others may not have this experience, but I thought you might like to know of someone who does. I just consider it a minor irritation--no more.
|
|
|
12-02-2004, 09:46 AM
|
#4
|
Montana Master
Join Date: Dec 2002
Location:
Posts: 1,804
M.O.C. #57
|
I've havn't had a problem filling ours. Like the above poist you may have a crimp in the line.
Gene
|
|
|
12-02-2004, 10:00 AM
|
#5
|
Montana Fan
Join Date: Sep 2003
Location: Plymouth
Posts: 253
M.O.C. #522
|
We had the same problem. Your solution will probably be the same as ours was. If you can trace the "vent tube" back, you will probably find that there is a kink in it at some place. All I had to do was cut off disconnect the vent tube, straighten the kink, cut off a bit of the length of the tube, then reconnect it. It seems that the "kit" that is given to the line workers putting in the tank and vent are given a length of flexible hose that is actually longer than needed, and instead of cutting it off at the proper length, the hose is just shoved in, often resulting in the kink. Oh... ...I also made a hole that the hose goes through a bit larger so there was not such a tight radius that the hose had to make.
P.S. After the fix, I can run the water into the tank at any pressure and not have any spurt-back.
|
|
|
12-02-2004, 10:00 AM
|
#6
|
Montana Master
Join Date: Nov 2002
Location: Weatherford
Posts: 1,383
M.O.C. #9
|
I use one of those hose end filters - it has a small diameter plastic tube to insert in the filler, so more air can be vented out than water going in. It takes a while, but I just go off and do something else and let her run a while.
|
|
|
12-02-2004, 12:48 PM
|
#7
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
We can fill ours with spigot on full blast and have no kickback. I agree there's likely a kink or blockage in the vent line. Takes maybe ten minutes to fill a completely empty tank.
|
|
|
12-02-2004, 01:06 PM
|
#8
|
Montana Master
Join Date: Jul 2003
Location: Clearwater
Posts: 10,917
M.O.C. #420
|
Hi Dave! Have no idea how to help you with the freshwater tank problem. Just wanted to say HI! to you and Kelly.
|
|
|
12-02-2004, 01:35 PM
|
#9
|
Montana Master
Join Date: Sep 2004
Location: sioux falls
Posts: 1,835
M.O.C. #2121
|
Hi, Dave. We had the same problem on our 2955. Bob discovered that the vent hose was crimped at the connection. The hose was too flimsy and bent at too hard an angle. Bob replaced it with a heavier reinforced hose and we've had no problem since. You do have to take the belly off to correct this. Hope this helps.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Fresh water tank fill
|
c214dick |
Montana Problems, Problem Solving & Technical Help |
9 |
04-19-2016 02:25 AM |
fill fresh water tank
|
Lack of HP |
General Discussions about our Montanas |
18 |
04-27-2014 03:06 PM |
FRESH WATER TANK FILL
|
artfuldodger |
General Discussions about our Montanas |
22 |
12-02-2010 12:55 AM |
fresh water tank fill
|
tgrucelski |
Montana Problems, Problem Solving & Technical Help |
4 |
04-04-2008 04:27 AM |
BLACK WATER TANK OVER-FILL
|
Go Pokes |
General Discussions about our Montanas |
17 |
01-10-2005 01:55 AM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|