|
11-19-2009, 01:58 PM
|
#1
|
Montana Master
Join Date: Feb 2005
Location:
Posts: 1,502
M.O.C. #3142
|
GFCI outlet gone bad
I had an electric heater plugged into the GFCI outlet by the kitchen counter this morning...next thing I knew I heard a vibrating noise. I just happen to look at that outlet and it was starting to spark...I hurried and disconnect the heater...it blew alot of the lights...when I remove the GFCI outlet it was a bit melted and the wires were also melted. I would of thought that this would of shut down b/f this happened..anyways I went out and purchased a new one...Sure hope that this doesnt go bad...Scary to have happen.
|
|
|
11-19-2009, 02:33 PM
|
#2
|
Montana Master
Join Date: Oct 2004
Location: Gardnerville
Posts: 749
M.O.C. #2165
|
A GFCI does not act as a circuit breaker for high current, but for unbalanced current, like when some of the current goes through you to ground and not back through the circuit. It sounds like there was a poor connection in the outlet that caused a lot of heat when you used the heater.
Poor electrical connections are one of the most common problems we seem to have.
Bob
|
|
|
11-19-2009, 02:52 PM
|
#3
|
Montana Master
Join Date: Feb 2005
Location:
Posts: 1,502
M.O.C. #3142
|
That is probably correct ...I should of replaced this earlier b/c I had noticed the bad connection within the GFCI. Thanks for the input.
|
|
|
11-20-2009, 01:58 AM
|
#4
|
Montana Fan
Join Date: Jan 2009
Location: North Vernon
Posts: 261
M.O.C. #9087
|
I hope you got a new gfi that clamps the wires in when you turn a screwdriver ,not one that you just push the wires in the back and a spring holds the wire. The latter make for bad connections, thus heat and problems.
|
|
|
11-20-2009, 06:16 AM
|
#5
|
Montana Master
Join Date: Feb 2005
Location:
Posts: 1,502
M.O.C. #3142
|
Yep, thanks the wires clamp in and that is how the original one was in.
|
|
|
11-20-2009, 06:32 AM
|
#6
|
Montana Master
Join Date: Apr 2009
Location: Murrieta
Posts: 5,816
M.O.C. #9257
|
I had a bad GFCI in my rig, but it was at the bathroom lavatory. When it tripped it would not reset. I never did find out what tripped it, unless it tripped right after my wife had finishing blowdrying her hair and as she unplugged it. I replaced it and it's worked fine ever since. It did control all the bedroom circuits, too.
I had a house GFCI fail the same way. I guess they can just fail this way (get tripped then not be able to reset). I think I would prefer this problem than all the arcs and sparks.
I'm glad to hear you saw it before it caused more damage (or a bigger disaster).
|
|
|
11-20-2009, 10:18 AM
|
#7
|
Montana Master
Join Date: Sep 2004
Location: Leona
Posts: 6,382
M.O.C. #2059
|
At different times, both the bath and kitchen GFCI plugs went bad. I just went out and bought some new ones, better than the OEM ones and haven't had an issue since.
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Help GFCI lacation
|
Simpson9508 |
Repairs & Service |
7 |
09-26-2016 02:01 AM |
GFCI Breaker
|
slfaircloth |
Montana Problems, Problem Solving & Technical Help |
7 |
05-10-2013 11:58 PM |
GFCI
|
mgdg |
General Discussions about our Montanas |
5 |
07-22-2009 02:18 AM |
GFCI failure.... what gives?
|
Art-n-Marge |
Repairs & Service |
9 |
06-15-2009 03:08 AM |
GFCI problems
|
SLM1949 |
Repairs & Service |
4 |
08-12-2008 03:48 AM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Disclaimer:
This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.
All times are GMT -6. The time now is 01:34 AM.