|
05-05-2015, 02:02 PM
|
#1
|
Montana Master
Join Date: Jun 2006
Location: Madison
Posts: 1,239
M.O.C. #5906
|
Do we have a slideout problem?
We have a 3700RL with the double slides on opposite walls in the living/kitchen area. Both sides operate with a single switch on the control panel. We've noticed that the last couple of times that we've closed the slides that the lower rear corner of the right slide that contains the dinette and sofa gaps by about a half inch. The gap extends upward about a foot The top has retracted tight as are the front end of that slide and all four corners of the slide on the other side. Both slides extend full and properly. Do we have a problem?
|
|
|
05-05-2015, 02:35 PM
|
#2
|
Montana Master
Join Date: Jun 2010
Location: Colorado Springs
Posts: 3,335
M.O.C. #10496
|
Is it maybe because the sheet metal skirting in that area isn't molded to present a flush appearance with the slide? Just guessing here...
__________________
2010 3150RL
LevelUp, Dual 6 volt batteries, Progressive Industries EMS HW50C, Honda EU2000i Generator, Bridgestone Duravis R250 tires, Torklift Glowstep Revolution Stairs, LED Tail lights
2015 RAM 3500 Laramie SRW LB CC Cummins 6.7L Aisin Trans B&W RVK3600
|
|
|
05-05-2015, 03:16 PM
|
#3
|
Montana Master
Join Date: Sep 2013
Location: Pensacola (mail forward service)
Posts: 3,198
M.O.C. #13740
|
When I had my slide problem before leaving florida where neither would work, when I did get the stuck solenoid to release...we id several extend/retract sequences. One of those wasn't normal with a gap at the bottom front of the dining slide. I really believe that it was a fluid thing as I went added some Catepillar anti-stiction fluid since we were doin several cycles. And it hasn't done the gap thing again so far. I would say to add some fluid if you still have room and are below the top full line when everything is retracted. What can it hurt? Here's hoping both of us don't see this again. John
__________________
2012 F350 6.7 L dually, 2013 3800RE with 6 pt leveling, Sumitomo 17.5" load range h tires, Samsung 18 cu ft residential fridge, 8k Morryde I.S. with disc brakes. Full timing since 2012.
|
|
|
05-05-2015, 03:26 PM
|
#4
|
Montana Master
Join Date: Sep 2013
Location: Pensacola (mail forward service)
Posts: 3,198
M.O.C. #13740
|
I was going to add, since the slide is kept square by the two "tubes within tubes" where you see the teeth on the bottom of them, is that I fail to see how these slides can work flawlessly every time...even though they are coupled together by the square bar you see (very small bar) due to friction of the tube within a tube. Metal on contact with metal is going to have a friction effect. Try lifting the corner where the gap shows when the slide is coming in. My guess is that the gap goes away and may not show again. Again, what you got to lose? John
__________________
2012 F350 6.7 L dually, 2013 3800RE with 6 pt leveling, Sumitomo 17.5" load range h tires, Samsung 18 cu ft residential fridge, 8k Morryde I.S. with disc brakes. Full timing since 2012.
|
|
|
05-05-2015, 03:42 PM
|
#5
|
Montana Master
Join Date: Jun 2006
Location: Madison
Posts: 1,239
M.O.C. #5906
|
We've been keeping the slide out racks and pinions and the piston lubed with the spray for that purpose. Even so, it's still metal on metal as you say. We're sure the fluid is at the correct level, but will double check. More testing is now on the agenda.
|
|
|
05-05-2015, 04:49 PM
|
#6
|
Site Team
Join Date: Jun 2011
Location: Wilsey
Posts: 18,799
M.O.C. #11455
|
Sometimes that can be a symptom of something small caught in the bottom of the slide when it closes. Folks have found dog and cat toys and other things caught in there.
__________________
Dick, Joyce, Diego, Picatso and Gustav
2017 3720 RL, and 2013 HC 343RL
Pullrite Hitch, IS, Disk Brakes, 3rd AC, Winegard Traveler, Bathroom door mod, Dometic 320, couch for desk swap, replaced chairs, sun screens, added awnings, etc.
|
|
|
05-12-2015, 06:24 PM
|
#7
|
Montana Master
Join Date: Apr 2009
Location: Murrieta
Posts: 5,816
M.O.C. #9257
|
The only time I noticed my slides not extending or retracting in a square fashion, I was fortunate to find the battery was almost dead. I had my slide disconnect so the converter didn't charge my battery. I put a battery charger on it and it started working again. Just my experience, this might not be your problem. But do check the battery voltage, that it's over 12.6 volts.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Similar Threads
|
Thread |
Thread Starter |
Forum |
Replies |
Last Post |
Slideout problem
|
Tail Lights |
General Discussions about our Montanas |
4 |
07-28-2013 02:57 PM |
Slideout problem #796372!!!
|
sfretts |
Montana Problems, Problem Solving & Technical Help |
7 |
04-16-2013 01:05 PM |
Slideout Problem
|
Dathan |
Repairs & Service |
1 |
03-02-2013 03:32 AM |
Slideout problem...Need help
|
snfexpress |
Montana Problems, Problem Solving & Technical Help |
6 |
10-04-2007 12:04 PM |
Slideout problem
|
alanzuck |
General Discussions about our Montanas |
7 |
10-11-2004 11:48 AM |
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|