|
05-09-2016, 06:26 PM
|
#1
|
Montana Master
Join Date: Apr 2006
Location: Mesa az
Posts: 2,952
M.O.C. #5651
|
Brake problems
Picked up rig to clean up for an upcoming trip. Brakes were almost non-existent on trailer set on 9 (normally run at 6.5 or 7). After 10 minutes or so with a few stops, they were up to maybe 15-20% of what they should be. If I took my foot off the brake at a stop light and held the controller all the way down, I would creep forward about 2-3 feet and then brakes would grab ahold. Kind of strange.
I was assuming I would have to take it in to dealer. So I hooked up pigtail and unhooked it about 4 times. Then to test, pulled the safety thing and tried to move forward. Wouldn't budge! Hooked everything back and brakes worked perfectly!!
From what I read on another thread, they mentioned wiring not quite crimped properly or with corrosion. So I am thinking maybe it is a bit of corrosion in the pigtail??? Comments anyone?
Thanks.
__________________
Tom and Gail
2013 Mountaineer 362
2012 Silverado 2500
|
|
|
05-09-2016, 07:52 PM
|
#2
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,697
M.O.C. #12947
|
Your drums may have had rust on them, both on the brake surfaces and the surfaces that the magnet contacts. It may have taken a while to break through the rust to get good braking action.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
05-10-2016, 01:19 AM
|
#3
|
Montana Master
Join Date: Apr 2004
Location: Ontario
Posts: 722
M.O.C. #1328
|
And the trailer wheels need to rotate for the brakes to engage! but 2-3 feet is too much. I agree it's probably rust.
__________________
Mike & Donna Ishler Ontario, NY KE2LU FN13
2017 3720RL TST S637's
2017 Dodge 3500 Laramie CTD 4x4 Auto
|
|
|
05-10-2016, 04:24 AM
|
#4
|
Montana Master
Join Date: Sep 2013
Location: Pensacola (mail forward service)
Posts: 3,198
M.O.C. #13740
|
And it may have been film corrosion on the pigtail connector...this why some put dielectric grease in the plug. John
__________________
2012 F350 6.7 L dually, 2013 3800RE with 6 pt leveling, Sumitomo 17.5" load range h tires, Samsung 18 cu ft residential fridge, 8k Morryde I.S. with disc brakes. Full timing since 2012.
|
|
|
05-10-2016, 07:08 PM
|
#5
|
Site Team
Join Date: Aug 2007
Location: Omaha
Posts: 6,750
M.O.C. #7560
|
If you have greased the bearing by using the zerk in the center of the wheel, you may have over greased and blown the seal thus putting grease on the brakes OR if you had someone check and grease the bearings they may have done this too. If they used a powered grease gun it's quite easy to do this. I'd take the wheels off and check to see if you have any grease on the the brake pads and etc.
I also agree with the previous two comments, that it could have been rust or corrosion on the brakes themselves or corrosion in the wiring harness. They do make some electrical grease you can put on or in the connections to keep corrosion from getting to the parts. If your unit has been setting for any amount of time and if it has been humid this could also be the cause of you problem.
|
|
|
05-14-2016, 05:54 PM
|
#6
|
Montana Fan
Join Date: Oct 2005
Location: Grand Junction
Posts: 246
M.O.C. #4854
|
I'd also check the wiring near the axels, I've had the wires come loose, then you only get partial breaking.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|