|
01-09-2010, 01:17 PM
|
#1
|
Seasoned Camper
Join Date: Jan 2007
Location: Wichita
Posts: 78
M.O.C. #6712
|
5th wheel kingpin release
My wife cannot always get the Dodge/Montana in a "no load" condition, or have enough upper body strength to release the kingpin jaws. Being a 4WD, the side of the bed presents an additional obstacle to her getting a good pull on the release.
Anyone aware of an electric/motor driven release for the kingpin jaws?? Any other suggestions (other than going to the gym more often)?
John Ware
Wichita, KS
|
|
|
01-09-2010, 01:24 PM
|
#2
|
Montana Master
Join Date: Aug 2006
Location: merced
Posts: 983
M.O.C. #6171
|
What brand hitch do you have?
|
|
|
01-09-2010, 02:30 PM
|
#3
|
Montana Fan
Join Date: Jan 2009
Location: North Vernon
Posts: 261
M.O.C. #9087
|
I always raise the trailer to where I can just see daylight between hitch and kingpin plate. Should be no load on truck then. Sometimes I need to move truck ever so slightly forward or reverse to take pressure off of jaws so that they release real easy. JME
|
|
|
01-09-2010, 02:36 PM
|
#4
|
Montana Fan
Join Date: Jan 2009
Location: Roanoke
Posts: 248
M.O.C. #9068
|
I carry a two step folding step stool in the main basement. I use it to reach the lock on the hitch and occasionally to pull the release. We both use it to reach up into the upper storage in the kitchen.
|
|
|
01-09-2010, 02:39 PM
|
#5
|
Montana Master
Join Date: May 2003
Location: New Bern
Posts: 4,294
M.O.C. #311
|
I back into the hitch and it makes it a lot easier to pull the release. I have a Reese 20K hitch. Hope this helps.
|
|
|
01-09-2010, 10:24 PM
|
#6
|
Montana Master
Join Date: Apr 2009
Location: Murrieta
Posts: 5,816
M.O.C. #9257
|
I do not believe there is an electric motor for what you seek. The jaws should be well-lubed (but not overly lubed - too messy) and easy to pull open. If not, then the posts about raising the trailer for that sliver of daylight between the hitch plates, or backing up or moving forward to release the tension should help, because it should not require a muscle builder to open the jaws.
If your assistant is height challenged the idea of the step stool sounds like it might work to gain a better angle.
|
|
|
01-10-2010, 01:48 AM
|
#7
|
Montana Master
Join Date: Feb 2003
Location: Belvidere
Posts: 1,834
M.O.C. #185
|
As said before, you need to have back pressure on the king pin before it will easily release. After backing onto my leveling boards...I immediately apply the brakes, while keeping your foot on the brake - engage the emergency brake then shift into park. This process will keep the back pressure on the king pin and you can release the hitch easily. I also carry a 2 step folding stool that I use if needed. If you had to pull forward to level...just back into the trailer lightly and do the above procedure. Works for me!
|
|
|
01-10-2010, 02:57 AM
|
#8
|
Seasoned Camper
Join Date: Jan 2007
Location: Wichita
Posts: 78
M.O.C. #6712
|
[smiling] I'll try again with my wife to help her develop the technique(s) to getting the jaws to release, and to use the step ladder.
And hopefully we'll have a good training session!!! :-)
Thanks everyone!!
|
|
|
01-10-2010, 04:11 AM
|
#9
|
Montana Master
Join Date: Sep 2007
Location: Texas City
Posts: 5,736
M.O.C. #7673
|
As Steves said. Have you ever noticed when you are not hooked up and you pull into a parking lot and put the truck in park. There is a little movement forward or backward, depending on the position of the pawls in the transmission and rear end. This rocking motion can be just enough to put pressure on the king pin mechanism. A lot more forceful when on a slightly sloped surface. That pressure has to be removed.
Good luck.
|
|
|
01-10-2010, 04:18 AM
|
#10
|
Montana Master
Join Date: Jan 2006
Location: San Antonio
Posts: 1,298
M.O.C. #5165
|
With a 4X4 truck and 18 inch tires, I use a small folding step to get a good angle to pull the release. It sure makes like simpler for me.
__________________
F-250 King Ranch Crew Cab 2012, Single Wheel, 6.7 L Diesel, Transfer Flow Internal 50 Gallon Fuel Tank, Upgraded Ford Software for 50 Gallon tank, 2006 3475Rl with Mor-ryde King Pin, 2nd AC, 2nd Battery, Pressure Pro TPMS, Wet Bolt Shackle Kit
|
|
|
01-31-2010, 04:39 AM
|
#11
|
Montana Master
Join Date: Jan 2005
Location: Marcus
Posts: 1,032
M.O.C. #2819
|
I have an older RBW 5th wheel hitch and what I have learned is I come to a stop. Chock the trailer tires, then put truck in reverse and put slight pressure against the pin. Putting it back in park and upon pulling on the handle it will release very easy. Being 6'2" helps too.
|
|
|
01-31-2010, 06:14 AM
|
#12
|
Montana Master
Join Date: Jan 2007
Location: Lobelville
Posts: 2,128
M.O.C. #6650
|
My Truck is a little different. So I have a 2' length of pipe and a pull rod to release the king pin lock, then I put the 2' length over the release handle and it releases very easy. I have the Trailer Saver Air ride hitch and the locking jaws is like the Class 8 Trucks use except the head is a little smaller. Its alway proper, after setting your Roto Choks or what system you use to keep the 5er from moving put the Truck in Reverse and move ever so slightly back and it will take the pressure off the King Pin. Good Luck. GBY....
|
|
|
02-01-2010, 04:02 AM
|
#13
|
Montana Master
Join Date: Jan 2005
Location: North Ridgeville
Posts: 20,229
M.O.C. #2839
|
Here is what we observe with our 16K draw tite hitch also on the Resse hitches. First of course try to release the hitch. NO go then take some pressure off the hitch by raising the camper a bit..no go. then this always works..If the last thing you did was to back into the camp site..bump the truck forward. If the last thing you did was to pull foward into the camp site...bump the truck back a bit.. This always works if the other things did not.....Give it a try next time. It always works better if one person is pulling on the release handle while the other is moving the truck....
|
|
|
02-01-2010, 04:47 AM
|
#14
|
Montana Master
Join Date: May 2007
Location: Weeki Wachee
Posts: 814
M.O.C. #7219
|
What works for us is if the site is level then we block the back trailer tires and back into the blocks. It doesn't take much. Lower legs and release the hitch. The key is to get the king pin forward of the locking jaws. Remember that and you have the problem solved. If your site is unlevel remember where the king pin is and compensate.
Hugh
|
|
|
02-01-2010, 06:09 AM
|
#15
|
Montana Master
Join Date: Dec 2006
Location:
Posts: 2,376
M.O.C. #6575
|
Quote:
quote:Originally posted by farmboy
I always raise the trailer to where I can just see daylight between hitch and kingpin plate. Should be no load on truck then. Sometimes I need to move truck ever so slightly forward or reverse to take pressure off of jaws so that they release real easy. JME
|
Pretty much the way I do it. I usually just slide the tranny in neutral though. I recall when I bought the fiver the dealer showed us everything except how to unhitch. We were on unlevel ground, and I sheared the cotter pin in the handle trying to get the jaws to release. A quick call to the dealer, slide the tranny in neutral, and pronto, the hitch is so easy to release.
|
|
|
02-02-2010, 09:05 AM
|
#16
|
Montana Master
Join Date: Nov 2002
Location: Oceanside
Posts: 20,028
M.O.C. #20
|
Chocking the trailer wheels, then backing the truck into the rig and setting the emergency brake works very well for us, both on this superglide and the Reese we used to have.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|